SELLING MMWS 462

[wap13]

I have a very minty 462 Randy has tinkered with. I really like the saw and dont need to sell it but it just sits here while I use my 500. Ran exclusively on amsoil dominator and E free fuel. I'd guess it has 10-15 tanks through it, call it 20 to be on the safe side. It has a WCS filter and I have a pic of the stock filter. Neither have ever been cleaned to give you an idea of how much (or little) the saw has been ran. Both filters included with the saw. Saw has never been cleaned either, again just as a rough reference on run time.

Would like $1,450 shipped (in the lower 48) PHO. Will throw in a brand new Stihl 32" B&C for the asking price.

 

[wap13]

Can get more pics if needed

 

[wap13]

Also look closely at the saw.....

Disregard the the train wreck of a shop in the background....

 

[mrxlh]

Also look closely at the saw.....

Disregard the the train wreck of a shop in the background....

Mines worse, much worse…

 

[wap13]

Guess I'm not getting notifications, just saw this and never did see the post from toolmaker.

Will try to keep up with this better.

 

[Lions fan]

Check your profile settings, your notifications could be turned off!

 

[ruqwknf27]

What part of Ga are you in ? Gadsden, Al here.

 

[wap13]

West Central, 1 county from the Al line. I can be in Auburn in just over an hour, actually went to Montgomery this past Tues.

 

[wap13]

tough crowd

 

[wap13]

Should have put in the original add would take trades, partial trades or could add cash for the right trade.

Main things of interest would be guns ar 10/15s, M1A, bolt guns, hand guns would like to try a G45, 19x or M&P 2.0, 1911s, etc, shot guns, ammo 5.56 3.0hate, 9mm, 45, 6.5 creedmoor, .280, 22, 22mag, 22 hornet, 30.06, 300wm, 338wm, and others I'm sure. Optics, lights, other "outdoors stuff" like packs, knives, axes, coleman lanterns, or wouldnt mind trying a petromax, etc.

I am picky but my interests are broad.

 

[whitesnake]

No trades for other saws I assume?

 

[wap13]

Maybe but likely not as I have more than I need/have time to run. Feel free to offer though. Only ones that come to mind would be a 2511, maybe 201 or 7900/10 or maybe a minty 064 (though doubt my hands would like it) or 288. Dont need any of those either but have always wanted to try one. Any saw trades would have to involve cash too.

 

[Catbuster]

Is this made before or after the case change?

 

[Woodslasher]

Is this made before or after the case change?

No V2 in the exh port, so pre case change I'd say.

 

[wap13]

I would have to defer to someone like Woodslasher or if you want to tell me how to check I would be glad to.

 

[maulhead]

I would have to defer to someone like Woodslasher or if you want to tell me how to check I would be glad to.

From my understanding reading this thread (linked below) and info gathered in this thread.

V1 had a horizontal white case sticker. V2 had a vertical silver case sticker.

MS462 Design Changes

The 462 has undergone some serious design changes. The case, cylinder, and piston are are different now. These two pictures show the changes to the slug and the cases. Old style. New style.

opeforum.com

 

[huskihl]

From my understanding reading this thread (linked below) and info gathered in this thread.

V1 had a horizontal white case sticker. V2 had a vertical silver case sticker.

MS462 Design Changes

The 462 has undergone some serious design changes. The case, cylinder, and piston are are different now. These two pictures show the changes to the slug and the cases. Old style. New style.

opeforum.com

This one definitely has the white early sticker on it

 

[wap13]

Looks like its settled then. V1 it is.

 

[wap13]

No love for the 462s? Bad timing? Priced too high?

 

[toolmaker]

No love for the 462s? Bad timing? Priced too high?

I have a 462C that was massaged by Mr. Fat fingers. He tells me it's one of the top running 462s' that he has built.