SELLING Hutzel saws

[EJ mcnamara]

selling these saws I also sell Oregon bars and chains and the sugihara bars I can woods port these saws and do a full blown race build on these

 

[ammoaddict]

Are you selling them on a website or eBay store?

Sent from my moto g(7) power using Tapatalk

 

[EJ mcnamara]

No sir not yet but I will be soon

 

[Czed]

@P.M.P.
Now's your time get one.
I've let guy's run my dunlap ported chusky 372
And every one of them has tried to buy it
Haven't even run the second one he did.

 

[Czed]

selling these saws I also sell Oregon bars and chains and the sugihara bars I can woods port these saws and do a full blown race build on these

Do you carry the 61/272 they just released?

 

[EJ mcnamara]

No but I’m gonna on the next order because I’m going to build a couple 288 cylinders on the 272 bottom ends

 

[Czed]

No but I’m gonna on the next order because I’m going to build a couple 288 cylinders on the 272 bottom ends

See that's innovation
The stihl guy's just put a 046 on a 044 and
Bam they're done.

 

[Logsdendave]

Somethings gone wrong I can’t see the pictures. Or prices!

 

[ammoaddict]

No but I’m gonna on the next order because I’m going to build a couple 288 cylinders on the 272 bottom ends

I didn't think a 288 cylinder would work on a 272 crankcase. I think a 281 maybe will.

Sent from my moto g(7) power using Tapatalk

 

[EJ mcnamara]

281/288 is the exact same cylinder except bore size the 281 is 52 mm and the 288 is 54mm

 

[EJ mcnamara]

And yes with work and base trimming the cylinder will work I’ve done it I have 54mm 272 pistons and 55mm big bore replate pistons there wiseco pistons and they will work in the 7900 Sachs big bore and 044/046 setup too

 

[EJ mcnamara]

 

[EJ mcnamara]

 

[ammoaddict]

281/288 is the exact same cylinder except bore size the 281 is 52 mm and the 288 is 54mm

I must have been misinformed. I had read the bolt pattern of a 288 cylinder wouldn't fit on a 272 case, and the stroke was longer on one of them, thanks for clearing that up.

Sent from my moto g(7) power using Tapatalk

 

[EJ mcnamara]

You have to slot the hole on the base and cut the base to fit the 272 saw it’s not exact fit but will work you have to use the these pistons to do it because of the rod the 272 is 12mm and the 281/288 is 13mm

 

[ammoaddict]

You have to slot the hole on the base and cut the base to fit the 272 saw it’s not exact fit but will work you have to use the these pistons to do it because of the rod the 272 is 12mm and the 281/288 is 13mm

Ok, so the information I read is mostly true because it it not a direct bolt on without modification. Thanks for the info.

Sent from my moto g(7) power using Tapatalk

 

[Eccentric]

Are you going to use the 281/288 crank, stroke the 272 crank, or run the 272 crank as is and alter the port timing to deal with the 4mm shorter stroke (compared to the 281/288 crank that their cylinders were designed for)?

 

[EJ mcnamara]

No I use the 272 stock crank here is one of my big bore pistons this is the 55mm I have the 54mm I have too this is a 12mm pin this piston can be used in the 044/046 stihl the 7910 Sachs big bore the solo 681

 

[Lightning Performance]

No I use the 272 stock crank here is one of my big bore pistons this is the 55mm I have the 54mm I have too this is a 12mm pin this piston can be used in the 044/046 stihl the 7910 Sachs big bore the solo 681

I'm interested in one of these pistons for something else and a long 60mm like the 3120 but checking all my options. Might need something shorter than that in deck height.... not sure yet. Still have some math and another piston to test fit and see where stuff lands.

Any word yet on the 880 clones?

 

[Cooper264]

I'm interested in one of these pistons for something else and a long 60mm like the 3120 but checking all my options. Might need something shorter than that in deck height.... not sure yet. Still have some math and another piston to test fit and see where stuff lands.

Any word yet on the 880 clones?

Ive been keeping a close eye on the 880 clones. Been wanting to do one with pretty much everything oem but the cases and handle.

They have just about everything out except for the tank/ handle assembly, top plastics, and break handle. might be one or two smalls that I may be missing.