Just PM for additional details and pictures. All prices INCLUDE shipping to anywhere in the Continental US unless you are on the Left Coast (if you are on the Left Coast PM for shipping quote) I can only attach 5x photos to start, but just ask I have plenty more.
SOLD
Have a arctic with 046 D cylinder. saw runs good. Has a base gasket delete and a little work on the exhaust port. Handles work great, probably the warmed heated handles I have felt on a Stihl.
$480 plus Shipping. PayPal F&F
Any questions on it just let me know.
Stihl 044 K&S P/C Long Block.
Crank turns over smoothly. Slight bit of play on flywheel side bearing. No scoring visible on P/C. Case bottom is in mediocre condition and shows wear. See pictures
$75 shipped in lower 48 except for Left Coast (PM for shipping quote). PM with any additional...
I buy fix and sell stihl tools, i prefer the old ones and this is a nice example of the Ss0, approx 58cc a nice mid range saw dating to around the mid 70s
# - No damage to it, looks good, a little paint wear but it all adds to it's character.
# - Has had carb ultrasonically cleaned and new carb...
I just found a REALLY nice unicorn and I have decided to sell my MS460 Magnum. All OEM & very clean as I hope you can see from the pictures. PHO w/ dual spikes, roller chain catch, decomp plug, OEM HD filter and Stihl Pre-Filter band $635 includes shipping w/ insurance via FedEx Ground signature...
Hey guys-
I rebuilt two pretty nice saws - one later poly flywheel bubble-top Stihl 066 and one later Husqvarna 288.
The 066 I built for an arborist buddy who ended up taking my 385. The short block I got from a member here- it was in good shape but had been hit by a tree and the tank and all...
I got an 064 with an OEM worm gear that seats unusually tight into the oiler and makes the clutch drum difficult to spin by hand. Seems to cause the chain to spin at idle until the saw warms up and it don't make it any easier to pull over, anyone have a similar experience? Ordered an AM...
I have a Stihl 461 PHO ported by Mastermind Worksaws. It has an unlimited 460 coil and muffler outlet has been opened up. I'm the only owner. The saw runs great, has only been used for firewood - probably 6-7 cords of run time since new. I don't have compression reading but am posting piston...
Hey Guys, i have Stihl 026 i was doing up for a friend, passes all tests, vacuum/pressure of crankcase and same with fuel tank, all seems in good condition for its age,
It has a Walbro wt194 carb fitted, new genuine repair kit, and main jet, My concern is with the settings of the carb,
The low...
I joined OPE a couple weeks ago after seeing Chainsaw Jim's 357XP Hybrid Build, & thought WOW I need to follow up on this Build.
It stared last Fall when I'd Purchased a J-red 2159 with a new OEM Top for my midsize saw.
When I got it back to the shop to investigate it further I'd realized the...
Looking for a 75cc+ saw or saws willing to trade a yz250f 2007. Have pictures of the bike if your interested. Pm me and we can talk more about the deal.
Nice 026. Jug has a decomp but I plugged it. New OEM fuel line and filter. Also new throttle linkage. Put a nice air filter cover and top cover on it. Overall pretty clean saw. Has some etching by the clutch as shown but it’s relatively clean. Compression is 165 ish. Saw has fixed H carb on it...
Hi guys! I have a question for the experts. I have a 440 that has had a few cylinder kits put on and the end result is the same, seizure. The two kits I've put on were both "Hyway Kit" the fist one was big bore and we replaced a seal when that rebuild was done. Ran 20 minutes and then seized...
Im thinking about building another 12mm 044 with a Slant fin KS cylinder and would like to see what all is out there as far as builders or bottom ends. I dont need a piston or cylinder, just a good solid bottom end.
Hi everyone, as some already know I ended up with a
New Stihl 362 MT, its sitting here unused and I would like
to swap for a Dolmar or Makita 6100.
I suppose this offer will applay to those in my durisdiction,
as complications arrise when I take a product in from outside
the EU, in plain words...
Hi everyone.
In a round about way I ended up with a new MS 362.
What am wondering is, has Stihl sorted the problems
related to dust getting into the carb, I've seen posts regarding
this, albeit old posts.
If anyone has any advise on how these saws are now coping
regarding dust getting...
Greenerpastures
Thread
air filter
ms 362
ms 362 air filter
stihlstihl ms 362
stihl ms 362 air filter
Hey guys does anyone know of a source for a 24” .404 pitch bar for a 661? I have a few rolls of .404 RS chain and am currently running a Stihl 32” bar. I’m fine with quality after market, just have not been able to find one. 24-25 inch would be ideal, Thanks
Slant fin 044 cylinder, don’t know whether it’s a 10mm or 12mm, it was in a parts lot my buddy Ken has. He can get pictures of the bore tomorrow in better light, this is just the cropped pic of a group of pictures he sent me of stuff he wants to sell. He says he would like to get $100 for it.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.