How To Remove Aluminum Transfer Without Acid

[Mastermind]

This place is off to a great start......and will only get better.

 

[cus_deluxe]

This place is off to a great start......and will only get better.

it sure is dude. watched these vids again today, good stuff!

 

[decableguy2000]

I have a question. How did you put the split in the mandrel and when turned down the spike did you turn the whole thing down or cut shoulder in it?

Jeremy

 

[Mastermind]

I turned it down, then parted it off at the length I needed.

The slot I cut with a hacksaw.

 

[decableguy2000]

Thanks for info

 

[Magic_Man]

I used a 16 penny finish nail with the head cut off, chucked right up in my dremel. Cut a piece of duct tape about 1" wide, stuck half of it to the face of the emery cloth, around the nail, and onto the back of the emery cloth. The spinning of the mandrel tightens everything up, just need the tape to keep it from slipping when you start.

 

[sefh3]

You can also stop by the local dollar store and pick up a wooden dowel for cheap. Chuck it in your cordless drill. Works great for those that don't have those fancy air tools.

 

[sefh3]

Funny story. I was one of those that was on the muritic acid for cleaning cylinders. After a month or so in the shop all of my tools rusted that were on my saw bench rusted out. This is a safer easier way to clean cylinders. Thanks again, Randy.

 

[Mastermind]

Treemonkey taught me this trick.

 

[Tor R]

Randy, when u make the disc for the 3M pad, how tight do you prefer to have them? I've gone 2mm less then bore, but should I go a bit more tight?

 

[Mastermind]

Randy, when u make the disc for the 3M pad, how tight do you prefer to have them? I've gone 2mm less then bore, but should I go a bit more tight?

I've started using the 3M balls. More better.

 

[paragonbuilder]

I've started using the 3M balls. More better.

Link?


Sent from my iPhone using Tapatalk

 

[sefh3]

I've started using the 3M balls. More better.

I would like to see what you are using. I found the 3m scotchbrite pads work great while using a wooden dowel. One size fits all.

 

[Mastermind]

http://www.amazon.com/Abrasive-Woven-Scotch-Brite-Polishing/dp/B00CNEV5P0

 

[Lone Wolf]

http://www.enginehones.com/abrasivehones.html

 

[Lone Wolf]

http://www.woodcentral.com/woodwork...08/md/read/id/178012/sbj/scotchbrite-ratings/

 

[exSW]

http://www.amazon.com/Abrasive-Woven-Scotch-Brite-Polishing/dp/B00CNEV5P0

Do they combine shipping? $5.80 per is a lot stiff.

 

[Tor R]

I've started using the 3M balls. More better.

what I love with this forum is how people try to help each other.
It's just awesome!!

I am not sure if I can get the 3M ball in Norway, else I have to go through Amazon, will check it tomorrow.
Right now I habe seversl red scotch pads left to use, is 2mm tolerance ideal or did you go tighter?

 

[Lone Wolf]

Do they combine shipping? $5.80 per is a lot stiff.

Try this. http://www.globalindustrial.com/p/t...mpaignId=C5E&gclid=CJbvo9jR_MoCFQJZhgodzeUGtg

 

[Lone Wolf]

Just put them on an air angle grinder with the roloc tip or what ever it is called. Roloc disc pad holder actually.