Search results

I did a search but didn't find much. So the saw will crank and idle fine you can flip it on each side and spin it around and it doesn't change you can even lightly touch the throttle and the saw will start to rev but the moment that the bottom throttle starts to open it bogs. I'm thinking that...

Ok have a 562 on the bench and don't have a removal tool is the tool for the echo 590 the same? The old tool I have for some of the older saws with 3 legs is too big to fit. I tried to knock this thing loose with a hammer and punch and it isn't budging. Not my saw so I would rather buy the...

Ok so I rebuilt this saw a couple months back and it's been running like a top for the tree company I rebuilt it for. The saw lost spark so it came back to me. I checked it over and everything looks good except there was no spark. So I ordered a coil and changed it out and it has good solid...

Ok so I built one of these and it runs pretty awesome. Used the factory cylinder and bought a hyway pop up piston for it. Timing for the saw is at 76/119/100 and pulls a 24 really well. The question I have is do these saws come with a limited coil ?? I ask because when I was trying to tune it...

So my buddy with the tree service was asking about the echo saws he has. He was saying that they don't seem to oil like new after about a year of use. I've not seen that before unless the oiler filter is clogged but he says that's not the issue. Any thoughts or ideas here? He didn't give me a...

Ok so I got a big bore pop up for this saw and did some port work on it, opened up the lowers some to match a little better to the piston and cleaned the piston up and took a little meat off of it. Numbers landed at Intake, transfers, exhaust 79/122/102 Saw seems to run pretty decent

Ok so the 066 I am rebuilding had swallowed something at some point and the exhaust port and piston were damaged. I had planned to port this saw as well but had to raise the roof a bit more than I had wanted to. So the final numbers I ended up with are intake,transfers,exhaust 82/118/94 So is...

So my buddy that runs a tree service just brought me an old 066 in decent shape. He bought it at a flea market for 60 dollars and wants me to clean it up and get it into running shape. So I'm surprised this thing actually runs but it's gonna need a piston and rings a cylinder hone, a clutch...

Well first one of these I've worked on. The owner broke off part of the crankshaft on the clutch side. He brought me the saw and I ordered a crank shaft from HLS well broke the saw down this evening and when I went to look at the new crankshaft it's completely different the OEM one had an actual...

So I've got 2 of these now the first one I put a meteor P&C on which I opened up the exhaust and raised it a small amount and put together without a base gasket and an open muffler. It runs rather nice with a 32 But I want to build another and go a little further off the rails. I'm thinking...

So I am just wondering if I'm the only one. I have a saw that was left to me from a very close person in my life who died last year. I am just now getting around to rebuilding the saw and man I'm gonna end up spending more to rebuild this saw than it's ever gonna be worth money wise. I already...

So I have a 350 that I ported about 15 years ago saw ran good for a couple years and died found that the crank case bottom half was cooked so I replaced it with a Chinese one, new bearings and seals. It hasn't quite run right since. I've torn it apart a few times now. I did find the new seal...

Ok so I ordered crank seals that were labeled from pro line to fit 045 but the flywheel side is way too big to fit about 24-25mm internal diameter and the crankshaft is roughly 19.6mm in diameter on the flywheel side. Can anyone tell me the correct part number for the seal I might need?

Ok so I need a flywheel puller for this old 045 to get the flywheel off to change out the seal. It is different than my other Stihl flywheel puller. Pic attached of the flywheel. Can anyone please tell me where I can purchase the correct tool to pull this? Thanks.

Ok so I bought one of these kits, cleaned up some of the rough bumps around the transfers and intake and exhaust. I installed the piston and went to install the cylinder and none of the screws would thread in I scratched my head for a minute and decided to pull the gasket to find that the...

Need a good recommendation for bearings and seals on a 350. I put cheap Chinese crap in and only got about 10 tanks of gas before the seals were leaking. I want to buy a quality set can someone point me in the right direction?

The Antique Machinery and Heritage Festival is happening this Saturday for anyone interested in coming out to show off some old saws. Not sure how many people are nearby but just wanted to throw it out there and see if anyone was interested in coming.

If a bar uses 104 dl of 3/8 how many drive links of .404 will I need? 32 inch solid nose bar.

So I have an older craftsman 4 stroke weedeater model number 021132 I have replaced the fuel lines and rebuilt the carb. The thing will start and run fine for about 1/3 to 1/2 a tank of gas and then just shut off. I'm guessing a coil issue, but the coil is NLA 792479 armature-magneto any ideas...

I'm thinking that my old 7900 needs a carb rebuild haven't pulled it apart yet, anybody know what rebuild kit I need? It is an older 7900 with a Zama carb.