I was thinking 6 dl not 5 or 7 but it has been a while and the number of pins on the rim/sprocket can change DL countIve looked and looked.... for you trying to understand... but all I can come up with,,,,it a husky mount, 36” prolly 11 tooth sprocket but it would seem it should be a hard nose..
I think GB bars would be be goodish and answer your email to your problem with the code...
Other than that some one said about bars and chains / fitment once the chain is over the bar. You should see 5 dl,, try it on a chain and bar combo yo know that fits..
ConfirmedBe careful there, at least on my saws, adding the adapter and fitting a 36 from an 066 to a 395 required 3 more DL IIRC.
Maybe someone here can confirm that.
Thanks. It’s a amazying how something that should be simple can turn into a pain in the a$$.
I don’t see anything that had the same numbers. One was close View attachment 189334
If I had the chain that was on it that would be easy. I was given only 24” chains.
Even more odd, as is should be 115. But definitely isn’tI thought those nice guys at GB would be helpful ..
I emailed from there web page on Friday Eve UK time. This morning (Monday again UK time ) I get a reply from
gary.green@gbforestry.com.au
Maybe worth following it up and sending him a pic.
.View attachment 189677
I appreciate all of the leg work.I thought those nice guys at GB would be helpful ..
I emailed from there web page on Friday Eve UK time. This morning (Monday again UK time ) I get a reply from
gary.green@gbforestry.com.au
Maybe worth following it up and sending him a pic.
.View attachment 189677
Visually looking at the top pic with the 114 chain; imaging splitting the chain at the bottom and putting it in the grove probably then the top pic looks like it would have an extra drive past the bar length.It just seems long for a 36”. Here’s my Stihl for comparison. The Stihl is the bottom picture. View attachment 189335View attachment 189336 Here’s a 114dl on it View attachment 189338View attachment 189339 it’s a lot longer than 114
Probly cuz you had a 7 tooth on the 66 and a 9 tooth on the husky, lol.
Really though, I’ve only noticed 1 dl difference from Stihl to husky. There’s always exceptions though.
Under dispute Kev...lolz.Confirmed
3/8, you havta add 2 or 3 dl using the Stihl setup with the adapter on a Husky
404, you havta add 1 or 2 dl using the Stihl setup with the adapter on a Husky
Not really under dispute bud, just two different experiences, probably due to any number of differences between the B&C's, rim drive, etc ..........Under dispute Kev...lolz.
Two dl is a whole long ways. without going to a bigger sprocket.
I am not familiar with the 404 adapters at all??
What is a 404 adapter ?
I have a 36" 3002 mount ES that wears 108dl of 404. Huge tail and a fat bar.IDK...under dispute!
Yep getting a little too loose with the writing their.
I guess I associate the widest stihl mount (14mm?) with 404 for some reason?
Definitely no relation there.
There must be a different adapter from the largest mount though. That is what I am not familiar with.
IDK...under dispute!
Yep getting a little too loose with the writing their.
I guess I associate the widest stihl mount (14mm?) with 404 for some reason?
Definitely no relation there.
There must be a different adapter from the largest mount though. That is what I am not familiar with.
Pics of an internal roller nose CN40...My CN40 is an internal roller nose tip. 3003 or D025. 117dl 404 7 or 8P
It will run HN with 128dl of 3/8. Came that way chewing on the bar.
41" to the forward mount slot.
44" loa
Bar numbers
S13/T
SN42-63SY
404
It has to be a 42" bar. It wears an odd drive link no doubt.