WANTED Stihl Bar tips

[Junk Meister]

I have a Stihl Bar # 3003 000 9630 It is a 25" 50GA 84DL 3 rivet tip
I found it in the scrap yard, Had a bad bend in it but now it doesn't. The tip was gone so now I need one.
From cross comparing a bit of fleebay I believe it is a NLA wide nose tip It measures 2-15/16" where the tip meets the bar rails. the ?tang is an even 2" wide and is 1-13/16" long I have called a few dealers and no luck. Information is scarce any one have one to Offer? at this point I don't mind if it will be a .063" or a .325 pitch. Let me know.

 

[Philbert]

Wonder if there are aftermarket suppliers? Maybe places like HL, Bailey’s, Madsen’s, Loggerchain, etc.?

Philbert

 

[singinwoodwackr]

I have a Stihl Bar # 3003 000 9630 It is a 25" 50GA 84DL 3 rivet tip
I found it in the scrap yard, Had a bad bend in it but now it doesn't. The tip was gone so now I need one.
From cross comparing a bit of fleebay I believe it is a NLA wide nose tip It measures 2-15/16" where the tip meets the bar rails. the ?tang is an even 2" wide and is 1-13/16" long I have called a few dealers and no luck. Information is scarce any one have one to Offer? at this point I don't mind if it will be a .063" or a .325 pitch. Let me know.

Like this? Actually, I think the black one is a Carlton


Aftermarket one...

 

[Shane¹]

Like this? Actually, I think the black one is a Carlton
View attachment 480978

Aftermarket one...
View attachment 480979

Those look familiar lol

 

[Cat 525]

I have a saw blade with a handle at each end. Does not need a roller nose that you can use till ya get the ionsereds going!

 

[Junk Meister]

I have a saw blade with a handle at each end. Does not need a roller nose that you can use till ya get the ionsereds going!

Will Be very difficult to man both ends of of said "Blade".
I need to slim down but prefer some other method.
Did this come off of a STRUNK Chainsaw?
Do the handles have markings for "Right and Left. ???

 

[Junk Meister]

Like this? Actually, I think the black one is a Carlton
View attachment 480978

Aftermarket one...
View attachment 480979

From some Pictures and details I have gleaned from the Bay the some of the black ones were shown next to Stihl packaging
I did start finding a few but most were vaguely described. or .063 I did find a 20" - .050G 3/8" that I am tempted to buy and put a .325 .050 on and put the 3/8" on my 24".
Maybe I should ask if one of yours is a 3/8" x .050" and if you will part with it? I will watch PMs and this thread.
Thanks

 

[singinwoodwackr]

From some Pictures and details I have gleaned from the Bay the some of the black ones were shown next to Stihl packaging
I did start finding a few but most were vaguely described. or .063 I did find a 20" - .050G 3/8" that I am tempted to buy and put a .325 .050 on and put the 3/8" on my 24".
Maybe I should ask if one of yours is a 3/8" x .050" and if you will part with it? I will watch PMs and this thread.
Thanks

All are 3/8. “White” ones are nos but have been around for a long time. The black one is brand new.
I don’t need all 3

 

[Junk Meister]

Wonder if there are aftermarket suppliers? Maybe places like HL, Bailey’s, Madsen’s, Loggerchain, etc.?

Philbert

I haven't stumbled onto a good number to start crossing from (Yet) or one that is .050/,058

 

[Junk Meister]

All are 3/8

I was hoping to stay away from the overly wide .063 gauge on the .050 bar.
I was thinking of converting the 20" .050" bar from 3/8" to.325" (I found those tips) then use tha 3/8" - ;050" tipon my 24" Bar.

 

[Shane¹]

I was hoping to stay away from the overly wide .063 gauge on the .050 bar.
I was thinking of converting the 20" .050" bar from 3/8" to.325" (I found those tips) then use tha 3/8" - ;050" tipon my 24" Bar.

Most replaceable tips are universal for all width bars I think.

 

[singinwoodwackr]

Most replaceable tips are universal for all width bars I think.

They are all .063

 

[Junk Meister]

All are 3/8. “White” ones are nos but have been around for a long time. The black one is brand new.
I don’t need all 3

I will pm you
I just saw they are all .063. but I'll still send you a pm

 

[Shane¹]

I will pm you
I just saw they are all .063. but I'll still send you a pm

I think what he is saying is all the replacement tips are .063 not just the ones he has

 

[Junk Meister]

I think what he is saying is all the replacement tips are .063 not just the ones he has.

I just checked my 36" Stihl bar .050 and a new .063 chain fits in the nose but not in the bar rails so that verifies what you just said. Might explain why I can't find what they never made.
Thanks for setting me in the right direction.
Now to see if I misunderstood what CAT 525 was trying to shovel with that two man contraption.

 

[singinwoodwackr]

I just checked my 36" Stihl bar .050 and a new .063 chain fits in the nose but not in the bar rails so that verifies what you just said. Might explain why I can't find what they never made.
Thanks for setting me in the right direction.
Now to see if I misunderstood what CAT 525 was trying to shovel with that two man contraption.

Ah, that makes a big difference. If the bar can be dressed (ground) to around .058 it would be worth a re-tip. If not…scrap metal…

 

[Junk Meister]

Ah, that makes a big difference. If the bar can be dressed (ground) to around .058 it would be worth a re-tip. If not…scrap metal…

I believe I can still run .050 on it, just clean the rails of surface rust. If Not then I will run it through the bar shop.

 

[singinwoodwackr]

I believe I can still run .050 on it, just clean the rails of surface rust. If Not then I will run it through the bar shop.

Well, if you want one of the white tips, $30 shipped.

 

[Junk Meister]

I will take it and my info is in the PM/DM
Thank You.
You get to choose which one to send.

 

[singinwoodwackr]

I will take it and my info is in the PM/DM
Thank You.
You get to choose which one to send.

Will go out tomorrow