Saw videos, T4driller 346xp, Rattler 2153, MOFO 026

[MustangMike]

Usually the chain catch is what starts jamming things up when noodling. For modding covers, I would keep the chain area covered, adding danger otherwise.

 

[Dub11]

Usually the chain catch is what starts jamming things up when noodling. For modding covers, I would keep the chain area covered, adding danger otherwise.

This is just for playing. I got extra covers for limbing duties.

 

[dolmarkid]

No mofo 044

 

[BuckthornBonnie]

AM covers are cheap and fit well. My cut one was dropped from a bucket truck so I just followed the crack lines and opened it up some.

 

[BuckthornBonnie]

We noodle a lot since we get tree service wood and burn anything. The 064 has an 8pin and 20"bar. It's tuned a bit rich since noodling is its only job.
That saw has a few AM parts (bearings, seals, Meteor, lines, etc. ).

 

[dustinwilt68]

No mofo 044

Mike this was 50cc testing, dnt worry soon as I get a few more 70cc saws the MOFO 044 will get its chance, have a hybrid coming to run against it

 

[dolmarkid]

woo hoo

 

[RI Chevy]

With the tip down, the noodles are not as long and stringy; therefore, they clear better.

Cool. TY sir. [emoji106]

I simply found it by trial and error. Lol

 

[bryanr2]

Mike this was 50cc testing, dnt worry soon as I get a few more 70cc saws the MOFO 044 will get its chance, have a hybrid coming to run against it

Run that 365 special in that test too.

 

[dustinwilt68]

I sure will, all my saws need broke in, just hard to get that many saws ported close togetjer and broke in

 

[MustangMike]

just hard to get that many saws ported close togetjer and broke in

Such a Problem ... !!! (In my best LIJ accent)!!!

 

[dustinwilt68]

I heat with wood and coal, last year we didn't buy any coal as we just burned .ore wood and saved the coal for night times, this year is looking the same,have to justify the saws some how.

 

[t4driller]

So how do you choose which saw to run?? Choose out of a hat or?? Enie, menie, minie ,mo

Sent from my SM-G930V using Tapatalk

 

[Dub11]

I would like to give everyone here a big round of applause! Last video thread I watch on another site with ported saw from different guys turned in to a full blown dumpster fire to the 10th degree!

 

[TreeLife]

I try to give attention to all of my saws...but I have a rager for my recently aquired cs2260...I loves it. It loves me.

Back on subject and to throw a twist into the mix: do you use 25°,30°, or something else for your cutter angle if you are noodling consistently?

 

[t4driller]

I try to give attention to all of my saws...but I have a rager for my recently aquired cs2260...I loves it. I loves me.

Back on subject and to throw a twist into the mix: do you use 25°,30°, or something else for your cutter angle if you are noodling consistently?

I think it still has the chain that was on it when I gave the 346 back. It had a 30 degree angle on top

Sent from my SM-G930V using Tapatalk

 

[dustinwilt68]

I would like to give everyone here a big round of applause! Last video thread I watch on another site with ported saw from different guys turned in to a full blown dumpster fire to the 10th degree!

Same here, not trying to start anyrhing between builders, I have had nothing but great results, and experiences with each and every 1 of them, I will have saws done be all of them again, each saw performed better then I expected.

 

[Dub11]

Same here, not trying to start anyrhing between builders, I have had nothing but great results, and experiences with each and every 1 of them, I will have saws done be all of them again, each saw performed better then I expected.

Oh I know you never had that intention I'm just glad no riff raff jumped in lol.

 

[dall]

Oh I know you never had that intention I'm just glad no riff raff jumped in lol.

but we did lol

 

[Dub11]

but we did lol

But hey O left my matches and gas can at home lol.