Not So Pro 3

[dall]

Just one pizza?

hes feeding a family of four he should have bought atleast 3 pizzas

 

[Mastermind]

Just one pizza?

He must be sick.

 

[Egg Shooter]

PM sent to the powder coater.

 

[p61 western]

Good evening mfers

 

[Mastermind]

PM sent to the powder coater.

That's the right way to do it.

 

[Czed]

Letting the virus build immunity is probably what gives the best immunity, but but, there is no one who has a health care system with overcapacity. When the hospitals are filled with covid patients, there are a whole bunch of people who remain in the health queue, and the loss of health means that the vaccine will win every day.

It's a whimsical world, people steer clear of the syringe and instead opt for Ivermectin.

There's apple flavored ivermectin horse wormer chewables
If you want me to send you some Tor?
They're probably 20 year's old
I saw them in a old feed store.

 

[Egg Shooter]

That's the right way to do it.

I'm to tear it down an clean parts of oil / grease b4 bringing them north. I'll start tomorrow. Anything worth doing is worth doing twice....

 

[dall]

I'm to tear it down an clean parts of oil / grease b4 bringing them north. I'll start tomorrow. Anything worth doing is worth doing twice....

lol

 

[p61 western]

I'm to tear it down an clean parts of oil / grease b4 bringing them north. I'll start tomorrow. Anything worth doing is worth doing twice....

Lol chit happens, but you won't be happy until it's right. With that being said I only did one full restoration, and it drives me nuts just looking at it. I like to run them.

 

[Mastermind]

I'm to tear it down an clean parts of oil / grease b4 bringing them north. I'll start tomorrow. Anything worth doing is worth doing twice....

Did I tell you about having to cut the floor outta my truck? Why? Because some jackass half did some "repairs".

 

[timg]

I'm to tear it down an clean parts of oil / grease b4 bringing them north. I'll start tomorrow. Anything worth doing is worth doing twice....

Exactly
The count don't matter.
End product always does!!

 

[GCJenks204]

I no longer believe a thing you guys have told me about @Woodpecker . Brad is no where near the dik you guys say he is.

 

[Kiwioilboiler]

The Boy wanted to look at what I'd been up to.
At midnight this bridge was flooding over. They put angled steel grates on the upstream side and it just pushes debris up against the bolsters. I just kicked or threw branches off the road.
A few years ago before the grates logs blocked it and was washed out. We were boxed in for a couple of days while they repaired it. Not quite as bad this time.

 

[GCJenks204]

I had the best time today watching a truck driver struggle to pull out of the yard. He couldn't comprehend that he had to swing it wide to make the corner. Our own drivers looked like they wanted to hang themselves just watching. It's really not a hard turn to make, and usually I would guide him out but this guy showed up with no appointment then took 45 minutes to get out of the damn truck and give me the paperwork so I could break the seal on the trailer.

You should see some of the guys try and back a 40ft container in to our side door. Sure it is 90degrees from straight back but there is a ton of room. Guys that can drive 5 minutes, back, forward to straight and then back to docked. Other guys 30 minutes later….

@Egg Shooter Steve I don’t need to quote and pile on, you’ve already made the correct decision.

 

[dall]

Did I tell you about having to cut the floor outta my truck? Why? Because some jackass half did some "repairs".

pictures slacker

I no longer believe a thing you guys have told me about @Woodpecker . Brad is no where near the dik you guys say he is.

View attachment 307387

we said he has the head shaped like a dick

 

[markds2]

You are right on both counts. We can't have our cake and eat it too. I will, however, use this on certain occasions. I just can't have paint raining off it.

I had the exact same experience Steve, I'll tag you into the build thread so you can see. Spent a huge amount of time and a considerable amount of money on the build, and although in my case I did use the proper etch primer (which stuck fine) the Valspar enamel I used was the problem. It was not at all fuel resistant (bubbled and fell off when the fuel vent leaked) and chipped very easily (like when the starter handle hits the recoil on retracting). The sad thing is being a powerful ported 92cc saw, I'm not trusting putting the main bearings back in it after beating on them to remove the crank, even though they have only done an hour or two of work, and believe me Stihl like charging for their (plastic cage) main bearings! Have to do the seals and gaskets too...

 

[Mastermind]

I no longer believe a thing you guys have told me about @Woodpecker . Brad is no where near the dik you guys say he is.

View attachment 307387

He's still a dik.....just not to you.

pictures slacker

I've not started cutting yet. Driveway project. Raining.

 

[Egg Shooter]

Did I tell you about having to cut the floor outta my truck? Why? Because some jackass half did some "repairs".

That sounds more fun lol.

 

[dall]

He's still a dik.....just not to you.



I've not started cutting yet. Driveway project. Raining.

were supposed to get a lot of rain tonight and tomorrow
Some say 5 to 6 inches

 

[Mastermind]

That sounds more fun lol.

They did patch panels from flat sheet. Didn't consider that the weatherstripping didn't have any groove to set in after their "fix".