SOLD MS661 with 20" Rollomatic ES 1100.00 Shipped

[Mastermind]

Took this saw in on trade in. It has been completely disassembled, inspected, cleaned, machined, ported, and reassembled with new gaskets, seals, rings, clutch cover, R model bucking spikes, 20" bar, and chain. Great running saw that is ready to kill trees.



Has a crack here on the foot pad. Doesn't leak anything, and seems solid. Uncracked on the bottom. Probably happened trying to get it unstuck.



Unsolicited air filter picture.

 

[Mastermind]

The other side...



Yep....new bar and chain.



Muffler has big hole and more open screen.



Another view of the crack.

 

[TreeLife]

That's a sweet deal, sure won't last long. Great model ported by a legend. Glws

 

[3120 addict]

Hi,

Think you may possibly have a similar 395xp that you have done your magic too at some point? Thank you.

 

[Mastermind]

Hi,

Think you may possibly have a similar 395xp that you have done your magic too at some point? Thank you.

No sir.

 

[Loony661]

Very nice, wish I had the greenbacks to buy this. I’m sure someone will snatch it up sooner than later!

 

[Mastermind]

Very nice, wish I had the greenbacks to buy this. I’m sure someone will snatch it up sooner than later!

I'll be changing the handlebar hose tomorrow.

 

[Mastermind]

Sunday special. Buy this saw today, and I'll throw in a 28" ES Light bar. It will also have new handlebar hose installed today.

So....a 20" bar and chain, and a new 28" light will be included.

Today only.

 

[Loony661]

Dang, this is a smokin’ deal!

 

[Mastermind]

Dang, this is a smokin’ deal!

I'm afraid that the crack in the tank handle is a turn off for some. I've been using the saw to knock down some big stumps. No problems. Runs great, pulls hard. The crack is just cosmetic as far as I can see. If not, I'd have replaced the tank. The piston was replaced with a low hour OEM one that I had on the shelf. New rings of course.....

 

[Loony661]

I'm afraid that the crack in the tank handle is a turn off for some. I've been using the saw to knock down some big stumps. No problems. Runs great, pulls hard. The crack is just cosmetic as far as I can see. If not, I'd have replaced the tank. The piston was replaced with a low hour OEM one that I had on the shelf. New rings of course.....

I wouldn’t be afraid of it one bit. Personally, I would throw on one of those $25-30 aluminum tank skid plates from ebay, and run it until it got worse. Then replace the tank housing as needed..

 

[Lnk]

I'm afraid that the crack in the tank handle is a turn off for some. I've been using the saw to knock down some big stumps. No problems. Runs great, pulls hard. The crack is just cosmetic as far as I can see. If not, I'd have replaced the tank. The piston was replaced with a low hour OEM one that I had on the shelf. New rings of course.....

Looks like a good deal, too bad I am so heavily invested in d009 bars. Not going to change now. GLWS!

 

[Mastermind]

Looks like a good deal, too bad I am so heavily invested in d009 bars. Not going to change now. GLWS!

Why would you have to? The saw comes with two new bars.

 

[Lnk]

Why would you have to? The saw comes with two new bars.

Because I have d009 bars from 16 to 42 inches, and I don't want them to get mixed up to where I have to read them. Lol

And other excuses!

 

[Mastermind]

This saw is SOLD.