A041 bar

[dahmer]

Does anyone make a decent quality A041 mount 18” bar, 3/8 lp/picco, .050, 62 dl? Not pleased with the Oregon single rivet offerings, that’s all I seem to be able to find. Thanks.

 

[Mycamaro_68]

I have modified several small Husqy mount bars to make them work for 041 mount. Might be easier to find a decent bar in small Husqy mount.

 

[dahmer]

I have modified several small Husqy mount bars to make them work for 041 mount. Might be easier to find a decent bar in small Husqy mount.

Lol. That will be a double mod! I’m modding the A041 bars to fit my Echo 490 that was modified to run 3/8 lp instead of .325. What’s a small mount Husky? K095?

 

[CJ Brown]

Yep K095. I don't have any 3/8 LP bars or I'd send ya one.

 

[dahmer]

Yep K095. I don't have any 3/8 LP bars or I'd send ya one.

I’ll check out a K095 and see how much I need to mod it. Thanks CJ.

 

[Mycamaro_68]

Does anyone make a decent quality A041 mount 18” bar, 3/8 lp/picco, .050, 62 dl? Not pleased with the Oregon single rivet offerings, that’s all I seem to be able to find. Thanks.

I don't know about longevity but Baileys carries these in a "universal mount" that I do know fits the 041 mount.

 

[dahmer]

I don't know about longevity but Baileys carries these in a "universal mount" that I do know fits the 041 mount.View attachment 351986

Thank you. Can’t be any worse. I’ll try one.

 

[Johnmn]

https://www.ebay.com/itm/382519427622

 

[dahmer]

https://www.ebay.com/itm/382519427622

Thanks. Only thing is all my chains are 91VXL062, however I do have to shorten the Oregon bar tails so that I can get the chains on, this may work. Thanks.

 

[Johnmn]

Thanks. Only thing is all my chains are 91VXL062, however I do have to shorten the Oregon bar tails so that I can get the chains on, this may work. Thanks.

I have used these bars on dolmar 421/Makita 4300's using a 62dl chain. I think you just have to trim a plastic tab on the clutch cover so the bar will slide back farther.

 

[dahmer]

https://www.ebay.com/itm/382519427622

Went buy it but “out of stock” came up when I tried to buy it.

 

[SOS Ridgerider]

Does it have to be 62dl? Cannon makes the SuperMini, which I think is 61dl. I have one of those bars, and it’s fantastic.

 

[dahmer]

Does it have to be 62dl? Cannon makes the SuperMini, which I think is 61dl. I have one of those bars, and it’s fantastic.

All my chains for the 2 saws are 62, about 10 chains. Depends on the bar, 62 may work or just have to shorten the tail a tiny bit. Thanks.

 

[dahmer]

Does it have to be 62dl? Cannon makes the SuperMini, which I think is 61dl. I have one of those bars, and it’s fantastic.

No go. All the Super Mini in the 18” 3/8lp are 66 dl. The hunt continues.

 

[SOS Ridgerider]

No go. All the Super Mini in the 18” 3/8lp are 66 dl. The hunt continues.

Ah! I didn’t remember correctly then. My apologies

Edit: Look up the 16” Super Mini. That’s a 61dl bar

 

[dahmer]

Ah! I didn’t remember correctly then. My apologies

Edit: Look up the 16” Super Mini. That’s a 61dl bar

Good thinking.

 

[SOS Ridgerider]

From the Cannon site:

Cannon SuperMini (Narrow Kerf) : CSM-C1-16-50-3LM – REPLACEABLE SPROCKET TIP, C1 Mount, 16 Inches, .050 Gauge, 0.370 Pitch (Low Profile), 61 Drive Links

 

[qurotro]

Maybe you can checkout some Echo bar?

 

[Duane(Pa)]

I think to run a KO95 on an Echo, you have to elongate the adjuster holes towards the stud groove. Pretty sure oil hole aligns.