FOUND IT 5ft or so of STIHL 19mm handle hose 0000 791 2009

[nv656]

looking for a chunk of 19mm Stihl or similar handle bar hose/tubing.

 

[singinwoodwackr]

looking for a chunk of 19mm Stihl or similar handle bar hose/tubing.

eBay has it in 5M pkgs. (16’) Not cheap, however.
Some dealers carry it and sell by the foot.

 

[nv656]

eBay has it in 5M pkgs. (16’) Not cheap, however.
Some dealers carry it and sell by the foot.

Yeah, seeing if anyone has a smaller chunk laying around so I can finish up a 090g wrap. I don’t think any dealers local to me have any in stock

 

[singinwoodwackr]

Yeah, seeing if anyone has a smaller chunk laying around so I can finish up a 090g wrap. I don’t think any dealers local to me have any in stock

I think the older models use a different diameter hose.

0000 791 2005 - STIHL HANDLE HOSE - USED FITS 032/051/075/076/088/090/MS 880/881 | eBay

0000 791 2005 - STIHL HANDLE HOSE - USED FITS 032/051/075/076/088/090/MS 880/881. PLEASE NOTE: Product images are for illustrative purposes only and may differ from the actual product. Due to differences in monitors, colors of products may also appear different to those shown on the site. 3:2

www.ebay.com

Or, it’s ribbed rather than smooth, don’t know.
@heimannm might have some he can sell you.

 

[nv656]

Don’t need period correct ribs, calls for 19mm 0000 791 2009 according to the parts book newer stuff has a different pattern but it’ll work.

I have the 2005/23mm and that does not fit.

 

[singinwoodwackr]

Don’t need period correct ribs, calls for 19mm 0000 791 2009 according to the parts book newer stuff has a different pattern but it’ll work.

I have the 2005/23mm and that does not fit.

I bet Mark has some

 

[Glock37]

Get a lot more than you need to get it on
I pressurize the hole 33 ft too put it on then cut it off as need once on

 

[nv656]

Very nice, unfortunately this isn’t my first rodeo with this stuff and the full wrap on a 090g is pretty open and forgiving. Only need a smaller chunk

 

[Glock37]

090 full wraps are some of the worst handles to install hose on
Takes 2 people to hold it abut no place to grap it because new hose goes there

 

[nv656]

Like I said, not my first time working with this stuff. Appreciate the input

 

[av8or3]

I’m pretty sure I have a whole roll I could sell you. I wouldn’t be willing to cut it up though.

 

[av8or3]

I got the complete roll.

 

[nv656]

Sent you a message

 

[nv656]

I got the complete roll. View attachment 482293

^

 

[av8or3]

I think I paid $80 for it. Plus a little shipping.

 

[Bill G]

I see you want it for a 090G. That was a saw I struggled with the hose on. Close to 20 years ago I bought a 090G on eBay for a pretty fair price. A gentleman north of me that I knew saw it and called asking if I would sell it to him. I already had a few 090G's and only bought this one because it was a good price. I figured I would sell it to him for what I paid. He did the same for me earlier on a very rare saw. When went to run it and look it over I noticed the full wrap had a crack in it where it attached to base. My aluminum and magnesium welding skills are not good so I took it to a welding shop. I wanted to pull off the hose so it did not get damaged but it was a huge pain in the rear. I ended up getting it pulled back enough to weld but it was tough. I paid to get it welded and lost money on the saw because I had already agreed to sell it at the price I paid