2152 options

[Johnmn]

Well I know I asked about a still 024 but I passed on that and got a jonsered 2152. Now my question is do I base delete, widen the exhaust, square the intake and muff mod the 2152 cylinder or do I order a 346 p&c? Thanks

 

[mdavlee]

Depends on if you'll be happy with 90% of 346 performance?

 

[WKEND LUMBERJAK]

Carl miller posted this yesterday

@Ronaldo this us for you. Lol. I told ya I had one close to done!

 

[MG2186]

I will say a 2152 in stock form is pretty depressing compared to a 2153/NE346. The 2152 cylinder will be easier to port with the removable transfer covers


Sent from my iPhone using Tapatalk

 

[Miller Mod Saws]

Well I know I asked about a still 024 but I passed on that and got a jonsered 2152. Now my question is do I base delete, widen the exhaust, square the intake and muff mod the 2152 cylinder or do I order a 346 p&c? Thanks

I would port or have that cylinder ported. For firewood duty I don't see the purpose of wasting a good cylinder that will run super good when ported. Will the 346xp out run it ported. All indications point to yes but is it really worth an extra $200 to say get 10% more. I personally like the 353 cylinder.

 

[Miller Mod Saws]

I will try and get a 325 vid soon. It takes a little bit lighter hand than I like to run this saw. But that said. This is a fresh build with 20" 3/8 lgx buried in oak. A lot of bar for a 50cc saw.

 

[Miller Mod Saws]

Carl miller posted this yesterday

Morning kenneth!

 

[cgraham1]

Mine has a ported 346 NE top end and a hda-199 carb. I like it.

 

[Johnmn]

I will try and get a 325 vid soon. It takes a little bit lighter hand than I like to run this saw. But that said. This is a fresh build with 20" 3/8 lgx buried in oak. A lot of bar for a 50cc saw.

Did you put an unlimited coil and 357 carb and intake on that saw? Seems to cut real well.

 

[Miller Mod Saws]

Did you put an unlimited coil and 357 carb and intake on that saw? Seems to cut real well.

Already had an unlimited coil when I received it. But it's the stock carb and intake tract.

 

[rburg]

Nice job as usual Mr. Miller.

 

[Miller Mod Saws]

Nice job as usual Mr. Miller.

Thank you!

 

[lwhaples]

I have two that go into the woods every trip.One is ported stock,the other has the a ported 346 top end.This year I may bring along a 357 or two.

 

[Johnmn]

Can't wait to pick up the saw I'm gonna need to quit work early one day so I can go pick it up

 

[Johnmn]

I will try and get a 325 vid soon. It takes a little bit lighter hand than I like to run this saw. But that said. This is a fresh build with 20" 3/8 lgx buried in oak. A lot of bar for a 50cc saw.

I would like to see a .325 video that's probably what I'll be running

 

[Miller Mod Saws]

I would like to see a .325 video that's probably what I'll be running

It will happen!

 

[Miller Mod Saws]

 

[Miller Mod Saws]

Same bar and chain that was run on the 5105 at the Iowa gtg. Havnt even sharpened it yet! Lol.

 

[MG2186]

That runs dam good, maybe I won't throw my 2 2152 cylinders a way. How's it compare to that 5105 you had up here this past weekend

 

[Miller Mod Saws]

That runs dam good, maybe I won't throw my 2 2152 cylinders a way. How's it compare to that 5105 you had up here this past weekend

I'm not sure. I need to run them side bye side. The 5105 is more quit and a lot more smoother. Little better behaved than this one. But dammer.aybe I can throw an edge back in the chain and try them side by side tomorrow.