Jusgunn3's latest activity
-
JJusgunn3 reacted to ErnieG's post in the thread Husqvarna 372 versus Husqvarna 372XPW versus Dolmar 7300 with
Like.
I have a 7300 and 372 both ported by Kris from S&S Worksaws ..I haven't ran the 7300 more then maybe a tank but I have ran the 372 a lot... -
JJusgunn3 reacted to farminkarman's post in the thread WANTED 562XP MK1 top cover, cylinder transfer caps, buffer bolt/bushing between fuel cap and purge bulb with Like.
Sounds like a plan!
-
JJusgunn3 reacted to Jazzlesaurus's post in the thread WANTED 562XP MK1 top cover, cylinder transfer caps, buffer bolt/bushing between fuel cap and purge bulb with Like.
Muffler mod and timing are the plan, maybe I'll do those things, reset autotune, time some cuts, swap caps, reset auto tune, and time...
-
JJusgunn3 reacted to farminkarman's post in the thread WANTED 562XP MK1 top cover, cylinder transfer caps, buffer bolt/bushing between fuel cap and purge bulb with Like.
If you aren't also altering port timing, I'm not sure you will see gains by swapping the caps. I wouldn't be surprised if it makes the...
-
JJusgunn3 reacted to Jazzlesaurus's post in the thread WANTED 562XP MK1 top cover, cylinder transfer caps, buffer bolt/bushing between fuel cap and purge bulb with Like.
Yup, 562 definitely has the stuffers. I had a 562XPG and enjoyed that saw quite a bit, but traded for a 395XP (turned out to have some...
-
JJusgunn3 reacted to hacskaroly's post in the thread WANTED 562XP MK1 top cover, cylinder transfer caps, buffer bolt/bushing between fuel cap and purge bulb with Like.
I believe this is so, similar to the 545 and the 550. The 550 has crank stuffers where the 545 does not. From what I understand that is...
-
JJusgunn3 replied to the thread Rakers too low.That’s a good point, I didn’t use a gauge on near end of life chain and the cutters where all over the place in size. Got some nice...
-
JThe beauty of the WCS and other progressive gauges. The teeth don’t need to be the same. It sets the raker to its tooth so they all...
-
JJusgunn3 reacted to rb924119's post in the thread Husqvarna 372 versus Husqvarna 372XPW versus Dolmar 7300 with Like.
100%. And I believe you’re correct for X-torq’s, but I run pre- X-torq powerheads, which are a bit lighter, I think.
-
JJusgunn3 reacted to huskihl's post in the thread Husqvarna 372 versus Husqvarna 372XPW versus Dolmar 7300 with Like.
I understand what you mean about liking or not liking the feel. It’s all part of why we run what we run. 7300 is actually almost a half...
-
JJusgunn3 reacted to Jazzlesaurus's post in the thread WANTED 562XP MK1 top cover, cylinder transfer caps, buffer bolt/bushing between fuel cap and purge bulb with Like.
I have not, I had seen a few folks saying they had good results getting a 555 close to a 562 with transfer caps and a muffler mod, which...
-
JJusgunn3 reacted to Jazzlesaurus's post in the thread WANTED 562XP MK1 top cover, cylinder transfer caps, buffer bolt/bushing between fuel cap and purge bulb with Like.
The bolt that goes into the spring, it's got a pretty big shoulder.
-
JJusgunn3 reacted to farminkarman's post in the thread WANTED 562XP MK1 top cover, cylinder transfer caps, buffer bolt/bushing between fuel cap and purge bulb with Like.
Have you run 562 caps on a 555 before? Without the stuffers on the crank, the transfer ports might need to be raised several degrees to...
-
JJusgunn3 replied to the thread WANTED 562XP MK1 top cover, cylinder transfer caps, buffer bolt/bushing between fuel cap and purge bulb.That is the av spring?
-
JJusgunn3 replied to the thread FOUND IT 562xp.I have projects if that is what your after