High Quality Chainsaw Bars Husqvarna Toys

Recent content by buckin-wood

  1. buckin-wood

    What's on your bench?

    picked up a Chinese RA handpiece a while back I've been meaning to try out. my kids RM85 top end had to come apart so I took the opportunity to touch up the ports :) for comparison #30, srcarr52 contra piece, Chinese RA flex shaft is a tight fit, might need to open the hand piece a tad...
  2. buckin-wood

    Welding save of a cracked 064 case

    no stacks of dimes were had. fooling around a bit on a junk case to see what I could do about fixing the mating surface... had the machine at 85A, but didn't need all of that to get a bead going on the edge. 2% ceriated, straight argon, AZ61A, left the balance at 9. I'll play with the...
  3. buckin-wood

    Welding save of a cracked 064 case

    you've inspired me to dust off the syncrowave. I assume I'm cranking the balance to 9? turning the little amp knob to 200.. mashing the pedal and magically beautiful stacks of dimes will appear ?
  4. buckin-wood

    What's on your bench?

    I spy a box from rockauto. hopefully you got a nice magnet or two :)
  5. buckin-wood

    What's on your bench?

    ouch, good luck. got to say that looks pretty bad. when I first split my cases I thought maybe I was dealing with a little surface junk... but after a quick blast in the cabinet it was clear the rot was much deeper. I'm sure people have fixed far worse, but not worth it for me.
  6. buckin-wood

    What's on your bench?

    on the bench... but for how long? I like a challenge! I'm going to clean out all the mag rot, tig up the craters, spend hours sanding it smooth as a baby's bottom, blueprint the cases, and should be good to go?! suppose I should powder coat it while I'm at it. probably strip the other case...
  7. buckin-wood

    17'bar

    I'm also here to see the 17' bar
  8. buckin-wood

    SOLD Dolmar XS 7910

    I'm in no rush. I assumed I was about a decade too late to land brand new red tops. this is exciting news to me. suppose this is probably the wrong area/thread to dish over sourcing dolmar parts from across the pond, eh
  9. buckin-wood

    SOLD Dolmar XS 7910

    thanks! now I need to find someone to order me a couple deckel rots and abdeckhaubes
  10. buckin-wood

    SOLD Dolmar XS 7910

    I would also like to know how to get my hands on a set of red covers :-)
  11. buckin-wood

    why port?

    I don't know about the cs310 in particular, but most any saw can be improved over the factory configuration. You'll be slightly limited because of the clamshell design. You can raise the exhaust and lower the intake, but can't easily move the ports in the other directions with just a...
  12. buckin-wood

    why port?

    people make small engine dynos, water brake, eddy current... I've seen some brake rotor setups that seemed to do ok. just need to measure the torque and RPM
  13. buckin-wood

    one saw that can do 20" and 16" bar?

    I thought tapping into the husqvarna auto tune bits required dealer access? Somewhere I've seen a part number for the interface cabling, but I'm pretty sure it still requires software available only to dealers.
  14. buckin-wood

    SOLD 2016 562xp, $250 shipped

    oh boy, how did I miss this one? still got it ?
  15. buckin-wood

    DOLMAR/MAKITA The Official Sachs Dolmar Dolmar Makita Dolmar Chainsaws Thread

    good work, cleaned up nice! usually I blast a saw pretty good with air to get most of the gunk off... but somehow I don't think even 165psi would have touched most of that. lol
Top