High Quality Chainsaw Bars Husqvarna Toys

Recent content by Benwa

  1. Benwa

    Show off your muffler mods

    Night and day difference with those two simple mods. The 192t is not even the same saw before and after. You'll love it! Mine lives with a 16" bar & has no problem with it after those mods. I think opening up the inner baffle makes a noticeable difference. I've noticed gains with as little as...
  2. Benwa

    Show off your muffler mods

    I don't. They're fairly time consuming. I just make them for personal saws at this point.
  3. Benwa

    Show off your muffler mods

    You need to! This was a stock saw with no other changes aside from the muffler swap. It picked up 9 seconds in the cut.
  4. Benwa

    Show off your muffler mods

    Made another Neighbor Waker Upper 9000 for a little husqvarna 350
  5. Benwa

    Just another 3120xp build......but it's MY first

    Man, I've been slacking haha. It's all together now. It's complete and I've made a handful of test cuts with it. I'm in the middle of two other saw builds right now so, the 3120 has to ride the pine for a bit. I'll get back into it though. Next things coming are the muffler mod is started, the...
  6. Benwa

    Messing around experimenting...guess my method

    I Think they're referencing the "mid post derail" about a potentially not so properly filed chain.
  7. Benwa

    The Swap Meet Thread

    Especially if it's the older style that uses the grub screws in the short chunk of fuel line for a vent. Surprising how easily they can get plugged.
  8. Benwa

    SELLING Husky 357xp / 359 Full wrap kit

    Everything arrived as described. Great packaging & easy transaction. Items were in like new condition. Thank you again so much! Can't wait to get them on the saw!
  9. Benwa

    Putting piston in reverse?

    Pictures online are so hard to "measure." For me, if the ring end gap is more than .100" away from the edge of the upper transfer port, I say run it. If it's closer than that, I'd run it backwards. I've run plenty of pistons backwards in saws without issue, but there's gotta be a viable reason...
  10. Benwa

    Admitting defeat

    I've shot my fair share (missed a few too) of racoons while standing 100ft or better from the house, in the snow in my boxers with just boots on. Haha. When the moment strikes.......... you gotta act on it! They're always after them, but get desperate in the cold, and give their best effort at...
  11. Benwa

    The First Saw You Bought

    Grew up with my dad running an Echo 500VL. When I was in my early teens it "died," he took it to the shop & it was too expensive to fix. He left it there and came home with a brand new Husqvarna 455. I was devastated. So many memories with him & that ol' Echo. I couldn't belive he just LEFT IT...
  12. Benwa

    Indian laurel/ficus

    That's a good move NOT running an air filter while milling. I never do either. They get in the way and makes a saw cut way slower.
  13. Benwa

    Show off your muffler mods

    Thanks so much for sharing! I was going to just drill out the spot welds, but obviously that wouldn't have worked. I figured I'd be in for a chore the first time I looked at my muffler with that tube in there. Thanks again. Off to the bench to start slicin' and dicin'!
  14. Benwa

    Show off your muffler mods

    Funny this popped up, I have my 3120 muffler on the bench. Would you be willing to show the other side of the muffler? (Opposite of the factory outlet side) Best guess from the photo, you just cut the area out where the support is spot welded in & then seal it back up? Thanks in advance for any...
  15. Benwa

    SELLING Husky 357xp / 359 Full wrap kit

    Thanks for looking out, I appreciate it. I sent him a PM.
Top