Dolmar 64xx/73xx/79xx series, smurfs and solo 665/675/681 thread

[KingCobra98]

You gotta split the can and reweld it.

Thanks!

 

[whitesnake]

You gotta split the can and reweld it.

A welder is not required.

 

[Wilhelm]

A welder is not required.

What he says!
Duck tape does the trick too, and if it doesn't hold You haven't used enough duck tape.

 

[Johnmn]

Pretty easy to heat up the crimped area and uncrimp with a pair of side cutters. Once that's done you can split the muffler, remove the cat crap and then reassemble, heating and recrimping as you go.

 

[Woodrow]

I know I could search on here but where can Dolmar parts be bought online? Also what rim drive does the 6400 take? Looking for a 3/8 7pin and 8pin.

 

[huskihl]

I know I could search on here but where can Dolmar parts be bought online? Also what rim drive does the 6400 take? Looking for a 3/8 7pin and 8pin.

SLE Equipment, The cutting edge, saw again.

Standard sprocket like an 044, 066, 372, 395….

 

[Wilhelm]

I know I could search on here but where can Dolmar parts be bought online? Also what rim drive does the 6400 take? Looking for a 3/8 7pin and 8pin.

Husky/Oregon large spline for the 64xx/6/73xx/79xx/90xx.
Any serious chainsaw dealer should have both 7 & 8 pin in stock.

Steve @166 for parts, don't know whether Nate @fordf150 still deals in parts after what happened with his shop.

 

[Wilhelm]

LOL

 

[davidwyby]

I’m looking for a teal carb support for a 6421/7900.
Beat deal I see is SLE $46.
Thanks

 

[Kiwioilboiler]

I’m looking for a teal carb support for a 6421/7900.
Beat deal I see is SLE $46.
Thanks

@mettee

 

[davidwyby]

@mettee

Rub it in…

 

[2StrokeJim]

Newbie here, not sure if i'm posting in right spot, i'm looking for an Alternative Engine Mount set up on ps-9010, Being i can't find OEM Mount's in The U.S. (Michigan) any Help would be Appreciated, and if i'm in the Wrong Spot feel free to delete my Question, Thank You

 

[mettee]

@mettee

I tried.

 

[mettee]

Rub it in…

We are.

 

[davidwyby]

We are.

Have hardly thought about the CF bars in a long time too. :-/ constant busy not really
keeping up with everything with only a little break here and there. Hopefully better after the new year. GTG time!

 

[dahmer]

Newbie here, not sure if i'm posting in right spot, i'm looking for an Alternative Engine Mount set up on ps-9010, Being i can't find OEM Mount's in The U.S. (Michigan) any Help would be Appreciated, and if i'm in the Wrong Spot feel free to delete my Question, Thank You

Might cost you a bit more but @Wilhelm has helped me with parts from Europe.

 

[mettee]

Have hardly thought about the CF bars in a long time too. :-/ constant busy not really
keeping up with everything with only a little break here and there. Hopefully better after the new year. GTG time!

I just need a bar milled so I can do the lay up.

And I need a vacuum assembly made that is two bars of aluminum. That way I can draw a vac and bake it.

 

[Wilhelm]

Newbie here, not sure if i'm posting in right spot, i'm looking for an Alternative Engine Mount set up on ps-9010, Being i can't find OEM Mount's in The U.S. (Michigan) any Help would be Appreciated, and if i'm in the Wrong Spot feel free to delete my Question, Thank You

Might cost you a bit more but @Wilhelm has helped me with parts from Europe.

The PS-9000/9010 AV mounts were still available from Germany when I made my last order.
But I wouldn't hold my breath as to the current situation as all Dolmar parts keep running out of stock and even NLA - especially parts for the PS-9010.

I am ramping up supply of smaller ticket spare parts.
If anything "big" goes on any of my saws it'll either be fixed through donor parts from another saw or the saw in question becomes a donor herself.

 

[SOS Ridgerider]

I’m looking for a teal carb support for a 6421/7900.
Beat deal I see is SLE $46.
Thanks

I just looked through my stash David. Red is all I’ve got too.

 

[Wilhelm]

I just looked through my stash David. Red is all I’ve got too.

What's the part number on the teal one?