"Crank Jack" Puller for MS660 case assembly

[afleetcommand]

Because folks have asked, I can replicate these if folks are interested one at a time. I will keep a couple MS660 versions built and possibly for other saws as well....PM if there is an interest

A puller to help in case assembly as seen on my video for MS660's.
Include:
1) One Handle
2) Two threaded rods, one with M12 x 1mm reverse thread tapped hole for the PTO side, one M10 x 1mm for flywheel side
3) Bushing
4) Nut & Washer.
5) Nut & Bolt for handle
Price $105 plus shipping. PM me if you want to buy one.
Note:Threaded rods in other drill & sizes available, $25 plus shipping

Currently Husqvarna typical M8 x 1mm and M12 x 1.25 reverse thread rods available as options. Concept being buy one complete "Crank Jack" and add additional threaded rods for different saws...bushing as well.


The "Crank Jack" Case Assembly Tool

 

[afleetcommand]

Current Orders will be shipped 4/8/17
Taking new orders for following week. I'll keep an up date here.

 

[MG porting]

Hey there are you still make the crank jack case assembly tool?? Need one for the ms660 and ms440.

 

[afleetcommand]

Hey there are you still make the crank jack case assembly tool?? Need one for the ms660 and ms440.

yup, message me. about a week or two from making another batch.

 

[MG porting]

yup, message me. about a week or two from making another batch.

OK sounds good.

 

[stihl_head1982]

Is this set of tools only good for the MS660? Just checking?

 

[afleetcommand]

I make them with any thread for any saw..assuming I have a tap...I currently cover most of the Husqvarna's and Stihls. U tell me what you need for a threaded end for the crank and I'll see if I have the tap. Common sizes I have been making incluse 10mmx1 8mmx1 12mmx1R and 14mmx1R I have the reverse in 12 & 14mm x 1.25R as well. A few others too as I've done a few "odd balls". A solution might be a person supply me with the drill & tap they need if it's really one off.

BUT if someone is serious about these, contact me on the messaging vs. here

 

[kanscruzer]

I need husqvarna 288 and I would like all husqvarna in that era 272, 262 ect

 

[afleetcommand]

I have m10x1 for the flywheel side, also m10x1R that some of the 272's have. I don't know what the 288's have. But PM me and we can discuss there

 

[kanscruzer]

I have m10x1 for the flywheel side, also m10x1R that some of the 272's have. I don't know what the 288's have. But PM me and we can discuss there

12mm x 1.25 LH

 

[MikebKy]

Because folks have asked, I can replicate these if folks are interested one at a time. I will keep a couple MS660 versions built and possibly for other saws as well....PM if there is an interest

A puller to help in case assembly as seen on my video for MS660's.
Include:
1) One Handle
2) Two threaded rods, one with M12 x 1mm reverse thread tapped hole for the PTO side, one M10 x 1mm for flywheel side
3) Bushing
4) Nut & Washer.
5) Nut & Bolt for handle
Price $105 plus shipping. PM me if you want to buy one.
Note:Threaded rods in other drill & sizes available, $25 plus shipping

Currently Husqvarna typical M8 x 1mm and M12 x 1.25 reverse thread rods available as options. Concept being buy one complete "Crank Jack" and add additional threaded rods for different saws...bushing as well.


The "Crank Jack" Case Assembly Tool

 

[MikebKy]

I will be starting a new 660 kit build soon and I am interested in your puller tools. I just watched your video on phase 2, have you progressed to phase 3 or 4. Any info would be greatly appreciated

 

[afleetcommand]

Best way to discuss that is to message me here of over at opeforum.com