Search results

Pro Mac 10-10s, selling for my neighbor, definitely has compression, haven’t had a chance to put gas in it and play with it. 24” bar on it he is asking $200 shipped. Pay pal f&f text me with questions 262-327-0018

Well, I haven't been on here in a while and I know everyone has just been on the edges of their seats wondering where I am and what I was doing. What have I been doing you say? Funny you should ask, I've been going to work a lot, those MFer's expect to see me there quite a bit, f-ing bullsh1t...

4 Carlton 3/8” Low-Profile chains. Three are 53 drive link one is 57 drive links. $40 for all 4 shipped in the lower 48 text me 262-327-0018

Hey everybody, I have a 28" Stihl guide bar to sell, its a few years old, i rarely use the thing. Its a standard plain jane bar. 3/8" pitch .050" Also included are 3 maybe 4 (3 for sure) Stihl full chisel/full skip chains I will post pictures in a sec when my phone cooperates. $50...

I have around 100 chains here that are used but still serviceable, still sorting them, most of them are under 20" and .325 pitch. Approximately 20-30 3/8" lo-pro I will update this post with sizes and quantities, looking to get $150 or so for all them if anyone is interested in just taking the...

Selling for a friend, autopsy looks like it ate the PTO side circlip. Mahle Slant fin cylinder is most likely junk, two notches on the edge of each upper transfer, deep gouges under the intake port (see piston pictures) Pulling the cylinder off was very difficult. Something is in the case...

There are ten new chains here. QTY 4- Windsor P/N 50APLG-66E 3/8"x.050" 66 DL Full Chisel SOLD QTY 2- Carlton P/N K1C-072 .325"x.050" 72 DL Semi-Chisel SOLD QTY 3- Carlton P/N N1 CBL 53G 3/8"LPx.050" 53DL Semi-Chisel QTY 1- Carlton P/N N1C-o57 3/8"LPx.050" 57DL Semi-Chisel QTY 1- Carlton...

I used up the 1/8" wheel that came with my Tecomec Super Jolly, well I didn't use it up all the way I dropped the f-ing thing and it cracked, either way, I don't have chains that need an 1/8" wheel, just use that size for my buddies stuff, so Im not buying a CBN wheel yet. I have two "Timber...

I have a large amount of Echo and Shindaiwa parts from a dealer that closed. All new, unused, in most cases still in the bag with a part number on it. Gaskets, hardware, recoil parts, carb parts, filters, trimmer head parts, plastic parts like triggers and filter covers etc. I am still sorting...

Stihl 031av Stout compression, seems to be well taken care of, stored without fuel in it and I have yet to fire it up. I will update this ad once I have fueled it up and attempted to run it. Not looking to make a ton of money here, it'll sit if it stays by me, I don't want her to dot if...

Farmertech cases, Hyway (?) Crank, Stihl OEM bearings and case gasket, Meteor piston. Case halves were cleaned and deburred before assembly, case gasket is OEM Stihl fresh out of a package. Farmertech/no-name anti vibe stuff, Meteor piston has no name wrist stuff just to hold it on there...

New, unused OEM Stihl parts..... I will add pictures later today H.O. Oil pump SOLD Fan/Flywheel housing, just the housing no recoil parts. SOLD Handle/tank assembly SOLD Large clutch cover SOLD Two pairs of crank seals $20 SOLD 3 pairs of 54mm caber rings $20 SOLD Four brake parts shown...

Meteor piston and cylinder for Stihl 066. Installed cylinder and timed it, nothing else. $70 via pay pal shipped within the US Text me 262-327-0018

Installed on a saw, took it back after about 5 minutes when I decided to sell the saw, includes the 4 pieces shown, like new. $75 shipped Text me 262-327-0018

064 for parts. I bought this about a month ago hoping it was a runner that I could use while I finished building an 066. There is too much going on with this thing, I do not have the time to get it where it needs to be. Long story short, I'm just too busy and pissed off about the situation to...

Looking for a Troy Bilt Horse tiller in S.E. Wisconsin 262-327-0018

I have an OEM Stihl TS350/360 Piston and Cylinder for sale, never installed on a saw. Piston, rings and cylinder, nothing else, not in a box, but clearly marked with Stihl casting and stamp marks. $250 Shipped Text me for pictures, I am having a hell of a time getting them from my phone to my...

Looking for an OEM Stihl 066 Piston and Cylinder that is unused, not on eBay. Cash or trade for other stuff. Not too worried about specific part numbers, don't know the specifics of the different types, don't care if its decamp or not.

I have a brand new, never used Farmertec Stihl crankcase splitting tool. Problem is, I also have one that I bought a few months back, I do not remember buying the first one, went out to the shop today cuz I actually took a whole day off and wanted to get my saw situation straightened...

Drew this, then had the laser dept. at work cut it, next one is gonna be thinner, when asked about material I just said "yeah sure whatever thinner gauge drops we have laying around" thing still weighs 9.5 pounds, gonna wear out the crank bearings before anything is built LOL 29" across, each...