Search results

Looking for a ms 291 p/c if anybody has a good one or even a cylinder that will clean up would work. Let me know what ya need for it. Lots of stuff to trade or greenbacks. Sent from my moto e6 using Tapatalk

Been there done that. We sold at least 100k feet to the amish north of here last year....it was good when we caught them at the mill. But every once in a while we had to unload them ourselves with the amish power tool, the can't hook! Sent from my moto e6 using Tapatalk

Im in! Sent from my moto e6 using Tapatalk

Big red hot needle, burns right through! Feels alot better when that pressure gets released too! Sent from my moto e5 play using Tapatalk

Have you pulled the muffler and checked the piston. I have had several of these trick me into thinking they had good enough compression to run and found that they were already slightly scored on the exhaust side of the piston.... Sent from my moto e5 play using Tapatalk

I have seen alot of posts on the interwebs on this subject as well. Despite all the possible problems with the misalignment i have successfully replaced case halves from donor saws on several different ones over the years, 2171, 372, 044,and 066. Never had any issues except for minor...

Found one of my homelite books and this is what i found.....anybody know what the letters at the end designated? That's the only difference i can see.... Sent from my moto e5 play using Tapatalk

Probably hard to cross reference but here is one of the numbers.... Sent from my moto e5 play using Tapatalk

I also have a question about this mess of 8800 stuff i was given the guy my buddy got them from had a bunch of modded 650's 750's and he was given these cylinders with another modded 8800. Both have the same bore but the muffler mount holes are different on one of them so i wondered if they...

Looking for id on this one boys. I was told it fits a 750 but not certain. I cant find my old ipls for this series of saws....thanks for any input! Sent from my moto e5 play using Tapatalk

Anybody got a cs8000 jug and slug they could part with? Sent from my Moto E (4) using Tapatalk

Carl we will take care of that part.... It's a muddy mess at the moment but I see a couple good days of sun coming my way so we should be ok..... Sent from my Moto E (4) using Tapatalk

If ya think you'll make it down to fort Scott for this one, throw your name on this thread! Lumberjackchef Rick Tucker Darick Rice Hedgerow Levi 67L36Driver Mo Jim Cobey Hinerman Sawnami WKEND Lumberjak moparnut88 Sent from my Moto E (4) using Tapatalk

You are correct Carl it is actually the 20th...I must have been breathing to many saw fumes lol! Sent from my Moto E (4) using Tapatalk

Morning all! Hope everyone is having a great summer... I too am ready for the leaves to change and the cool weather to start.... Darick and I were set up at the Lamar Free Fair this week and had a great time over there. Very nice people and a really great setup for a fair. Everything was right...

Yes Rick Tucker.. Sent from my Moto E (4) using Tapatalk

Went out to my buddy Rick's place the other day to help him with a few carbs and such. We pulled this ole girl out and finally got her running... 150psi , new China carb, scavenged a fuel line out of a donor 041 And fixed the intake gaskets. Fired up on the second pull!!! Now just need to find...

I will see what I can do .... Maybe make a short one just for you guys to check it out.... Sent from my Moto E (4) using Tapatalk

A buddy of mine came across the homade dual bar in a trade deal. I finally got my mill ready to go so it would mount up and made up a loop of chain. Ended up needing 170 drivers... It does make quite a bit of difference having the extras saw on board...they are still thirsty however.....1/2 tank...

No doubt! Malia is getting married this afternoon and of course we have 75 yesterday and 45 today. I milled up some cedar logs last week and put this together for them to say their vows under..... Hopefully the sun will at least shine for the ceremony ....... Have a good day gents! Sent from my...