why does H&L supply say 372 Hyway bb kit wont work on xtorque ?

[Willoughby]

why does H&L supply say 372 Hyway bb kit wont work on xtorque model ?
I wanted to order a bb pop up kit for my 372 x torque but it says it wont work , does any one know why ?
I was expecting to replace carb, intake, air horn, and top plastic to make it work but is there something im missing here ? thanks in advance for any replies

 

[P.M.P.]

I dont see why it wouldn't work.

Cant believe @Stump Shot hasn't jumped in here yet.

 

[Stump Shot]

I dont see why it wouldn't work.

Cant believe @Stump Shot hasn't jumped in here yet.

Waiting for you to ask first.

why does H&L supply say 372 Hyway bb kit wont work on xtorque model ?
I wanted to order a bb pop up kit for my 372 x torque but it says it wont work , does any one know why ?
I was expecting to replace carb, intake, air horn, and top plastic to make it work but is there something im missing here ? thanks in advance for any replies

They say that as it's not a direct replacement, as you already know, an adaption needs took place to make it work.

 

[beaglebriar]

why does H&L supply say 372 Hyway bb kit wont work on xtorque model ?
I wanted to order a bb pop up kit for my 372 x torque but it says it wont work , does any one know why ?
I was expecting to replace carb, intake, air horn, and top plastic to make it work but is there something im missing here ? thanks in advance for any replies

All you need is a 385/390 intake boot. Use the XT carb and elbow.

I'll take the XT parts off your hands if you decide to part with them.

 

[Stump Shot]

All you need is a 385/390 intake boot. Use the XT carb and elbow.

I'll take the XT parts off your hands if you decide to part with them.

... and, if you go this route, leave the divider in the carbeltater. Elbow is okay too.

 

[ammoaddict]

... and, if you go this route, leave the divider in the carbeltater. Elbow is okay too.

What in the heck is a "carbeltater"? I don't think my saw has one of those.[emoji1]

Sent from my Moto G (4) using Tapatalk

 

[Hinerman]

What in the heck is a "carbeltater"? I don't think my saw has one of those.[emoji1]

Sent from my Moto G (4) using Tapatalk

And they think we talk funny...

 

[Stump Shot]

CARBURETOR

 

[PA Dan]

CARBURETOR

Why are you shouting...?

 

[Stump Shot]

Why are you shouting...?

Dramatic effect.

 

[qurotro]

The XT engine shroud is taller than OE too if you dont mind that.

 

[Willoughby]

thanks for sharing your knowledge , very helpful thank you all

 

[Stump Shot]

The XT engine shroud is taller than OE too if you dont mind that.

Also has the decomp hole that is no longer needed. I usually fill it with epoxy to keep the air flow going past the cylinder. It's probably just me worrying too much, but it certainly can't hurt anything.

 

[Willoughby]

one more question I bought caber 52 mm rings for my Hyway kit and the rings are to thick for any piton I have -had to use the kit rings ?

 

[Stump Shot]

one more question I bought caber 52 mm rings for my Hyway kit and the rings are to thick for any piton I have -had to use the kit rings ?

Measure the thickness of the rings supplied and see if those are available in the Cabers.

 

[Willoughby]

Measure the thickness of the rings supplied and see if those are available in the Cabers.

I didn't know you could get different thickness rings - haven't seen that listed just size in mm 50 52 ect ?

 

[Willoughby]

Also has the decomp hole that is no longer needed. I usually fill it with epoxy to keep the air flow going past the cylinder. It's probably just me worrying too much, but it certainly can't hurt anything.

why would you want to delete de comp valve ?

 

[Stump Shot]

why would you want to delete de comp valve ?

The valve on an oe 372 is on the side a xt 372 angled on the top.

 

[Ketchup]

why would you want to delete de comp valve ?

They’re also a common air leak/ failure point. Old argument, but lots of people plug them.

 

[Mastermind]

I didn't know you could get different thickness rings - haven't seen that listed just size in mm 50 52 ect ?

Rings for a MS460 are 1.2mm