SELLING Stihl 260

[Cpedersen518]

Full rebuild, everything oem. Bearings, seals, piston, wrist pin, gaskets, new tank handle from China but seams good pluse it has a clear tank . New oem fuel cap. Paint is only missing cause the guy be for me ran no dogs and the bearings weren't bad I just wanted to replace them and the seals cause it sat along time and no it wasn't blown up just disassembled for some reason I don't know .also muffler modded and timing advanced .022 . Setup for .325. $350 odo

 

[Cpedersen518]

Oh a couple of fins on the cylinder is broke but I asked a couple guys and they said it's fine and also has a new cord too . Yes it's the 50cc cylinder

 

[drf256]

Nice saw.

Pics of cylinder?

 

[paragonbuilder]

Oh a couple of fins on the cylinder is broke but I asked a couple guys and they said it's fine and also has a new cord too . Yes it's the 50cc cylinder

Clean saw!
Pics of how bad it is? I wouldn’t want to work it hard if it was missing more than a corner or two. They dissipate heat.

 

[Cpedersen518]

Here are some more pics

 

[Cpedersen518]

Here's the cylinder. I do have a 026 decomp cylinder coming and a meteor piston for it so I'm going swap it out

 

[Cpedersen518]

Pic

 

[Moparmyway]

Full rebuild, everything oem. Bearings, seals, piston, wrist pin, gaskets, new tank handle from China but seams good pluse it has a clear tank . New oem fuel cap. Paint is only missing cause the guy be for me ran no dogs and the bearings weren't bad I just wanted to replace them and the seals cause it sat along time and no it wasn't blown up just disassembled for some reason I don't know .also muffler modded and timing advanced .022 . Setup for .325. $350 odo

Oh a couple of fins on the cylinder is broke but I asked a couple guys and they said it's fine and also has a new cord too . Yes it's the 50cc cylinder

Here's the cylinder. I do have a 026 decomp cylinder coming and a meteor piston for it so I'm going swap it out

I’m confused.

Its for sale with “a couple of fins on the cylinder is broke” for $350

Then a picture of a butchered cylinder that has most of it’s fins missing that I wouldn’t sell to Fred Flintstone, let alone the good dudes here at OPE.

Convienently, you didn’t show a picture of the cylinder, untill you were asked for one, probably because you were trying to get over on us .......... how else should I see this ?

Then you’re replacing the cylinder

You know what ?

I’m not confused now that I’ve put things down and read everything. I wouldn’t buy anything from you, even if you paid me

 

[Cpedersen518]

I’m confused.

Its for sale with “a couple of fins on the cylinder is broke” for $350

Then a picture of a butchered cylinder that has most of it’s fins missing that I wouldn’t sell to Fred Flintstone, let alone the good dudes here at OPE.

Convienently, you didn’t show a picture of the cylinder, untill you were asked for one, probably because you were trying to get over on us .......... how else should I see this ?

Then you’re replacing the cylinder

You know what ?

I’m not confused now that I’ve put things down and read everything. I wouldn’t buy anything from you, even if you paid me

You buy anything or do you just troll people ? I was honest and said it had some broken fins . Everything is new other than the damn cylinder . It wouldn't be the first saw with a few busted fins . I also figured it was excessive so I have a new newer cylinder on the way and another new piston for it

 

[Moparmyway]

You buy anything or do you just troll people ? I was honest and said it had some broken fins . Everything is new other than the damn cylinder . It wouldn't be the first saw with a few busted fins . I also figured it was excessive so I have a new newer cylinder on the way and another new piston for it

You said a couple of fins were broken, you asked some guys, its fine.
That aint fine to me, thats an abortion that I would only run on my own saw

You took a picture of the cylinder in the only angle possible that would show no broken fins

Others asked for more pictures and then the butchered cylinder appeared along with tales of replacement parts to be swapped out

That aint honesty, thats deceit

You have the gall to question someone asking about this abortion that you advertised in the for sale area ?

I’ve got over 20 saws, only a few were purchased new, where do you think the others came from ?

 

[Cpedersen518]

You said a couple of fins were broken

You took a picture of the cylinder in the only angle possible that would show no broken fins

Others asked for more pictures and then the butchered cylinder appeared along with tales of replacement parts to be swapped out

That aint honesty, thats deceit

You have the gall to question someone asking about this abortion that you advertised in the for sale area ?

I’ve got over 20 saws, only a few were purchased new, where do you think the others came from ?

If you look I posted 3 pics in a row I was posting pics of the saw being slit not the cylinder. I would have posted more soon but been at work . Really don't care what you think personally anyone else can see I'm not being shady . If that was the case would I have said anything?

 

[Moparmyway]

If you look I posted 3 pics in a row I was posting pics of the saw being slit not the cylinder. I would have posted more soon but been at work . Really don't care what you think personally anyone else can see I'm not being shady . If that was the case would I have said anything?

ABSOFRIGGINLUTELY positive now .......

You posted it for sale on Saturday

You only came clean today after being asked for more pictures, conveniently omitting the shiity cylinder untill today

Today is Tuesday, your intentional deception isn’t appreciated here ...........
@Mastermind
@Jon1212

 

[Cpedersen518]

ABSOFRIGGINLUTELY positive now .......

You posted it for sale on Saturday

You only came clean today after being asked for more pictures, conveniently omitting the shiity cylinder untill today

Today is Tuesday, your intentional deception isn’t appreciated here ...........
@Mastermind
@Jon1212

Here probably dont even think I put new bearings or anything in too rite

 

[lehman live edge slab]

He honestly was looking for a cylinder on here to put on this saw. I sold him a good cylinder and piston of an 026 pro. It has been slow getting there because the post office must have misplaced it for awhile.

 

[lehman live edge slab]

This is our conversation notice the dates, post office was slow and while I agree that is more than a little damage I think people have different views on what’s ok to run. I did find an almost new 026 piston for him to go with this cylinder in photos. This was for this saw

 

[lehman live edge slab]

I do think this was mostly a misunderstanding, the people he asked for a cylinder opinion have different thoughts then a lot of people here. He posted want add on this cite looking for a cylinder and piston to fix this saw rite. Hope this can all just blow over and stuffs back to normal.

 

[Moparmyway]

Has nothing to do with his original post trying to sell it with a couple of broken fins and purposely leaving out pictures of it.

Post up the pictures of the cylinder, be honest, upfront and true. Say that the cylinder on it is getting replaced or better yet, wait to post it for sale until its ready for sale

I’ve fixed stuff for guys after they were deceived and I’m absolutely not going to sit by and watch someone else get taken advantage of

Misunderstanding my azz ............

 

[lehman live edge slab]

Ok, I didn’t know it would even be up for sale without new cylinder. And I do completely understand where you’re coming from have been hosed myself a few times. And I was trying to just fill in some blanks is all no hard feelings to anyone.

 

[Jon1212]

I'm here @Moparmyway

 

[Deets066]

I'm here @Moparmyway