Saws you would like to see the manufacturers build or release

[rocco490]

So whats everyone wishing for or waiting for to come out?
Heres my list not in any particular order
Husqvarna 572xp
Husqvarna 390xp stroker with 40mm stroke and spot on port timing they could just call it the 590xp
Sachs dolmar ps 6100 big bore to 70cc
those are mine lets hear yours

 

[HighCountryTimber]

Stihl to go back to building a real 026,038 Mag II,044,044.066,088 not the current junk piles.

 

[rocco490]

I really enjoyed the 661 I ran the other day and couldn't say that about the 660 I had which is why I sold it. But I figure your making a living with timber falling by your name and I only do part time arborist work and firewood selling so your no doubt using your saws a lot more than me. I enjoy all the brands and have no complaints with any for my more limited use

 

[rocco490]

only saw I have had that was getting ready to fail on me(I didn't even know it) from bad workmanship wasnt a stihl it was a husky 550xp. randy ported it and when he tore it down it had a bad seal on I think the cylinder from someone at the factory messing up on assembly

 

[Tor R]

Get rid of that joke 543 and make one mini 550 xpg, 542xpg!

 

[nnero]

A bigger version of Dolmar 6100 (with mag clutch cover) that doesn't say Makita on it...

 

[pro94lt]

MS202T. Oh just make the 200t mtronic, that would be the day!!!

 

[jmssaws]

064

 

[Guido Salvage]

Stihl to go back to building a real 026,038 Mag II,044,044.066,088 not the current junk piles.

High Country Timber, wasn't that the name Hillbilly Redneck used on YouTube?

 

[R2D]

595xp but as light as a 390

 

[pro94lt]

595xp but as light as a 390

That's just asking to much!!!

 

[Tor R]

540 with rear handle, named 539XP. Would prefer them to stuff in G as well, would be nice to use Husky instead of those MS 201!!! My last 201 was borrowed away, i dont care if I get it back, piece of junk.

 

[R2D]

That's just asking to much!!!

395 17.4lbs
stihl competition is 16.6lbs
390 15.7lbs

how about 595xp matching the weight of 661?

 

[CR888]

Factory pipe saw 70-90cc's.

 

[Guido Salvage]

Poulan 8500 for $449.

 

[mdavlee]

Have an American made Poulan or Mac saws with some improvements to fit in todays spring av and better power to weight over the European saws.

 

[ajschainsaws]

A dolmar range that goes up too 118cc again

 

[Simondo]

I would like the main saw makers to find another way to build saws that satisfy emissions without going down the "Electronic carb/management " rout . Try getting to grips with a modern car/truck/lory...etc , without a large amount of diagnostic equipment that enables even the basics to be undertaken...hope another way can be found with 2 stroke engine to make them simple to run and maintain or its likely to be a main dealer trip for everything.

 

[Tor R]

I am sorry to say Simon but I think we only gone see new chainsaws with more and more electronic, when next generation autotune arrive I think we gone see autotune on homeowner saws also.
We have seen in car industry that before or later there come 3th party diagnose tools, it's more a question about time before the same happen to chainsaws as well.
The cheapest diagnose tool worked as a champ on my VW Passat, can read off errors and reset different brains, and such a tool would be more then good enough for us....

 

[Czed]

288 Xp or lite and 044 in the stihls