SELLING Not enough room

[Bryan Barrow]

In a couple months I will be moving into an apartment with my best friend. I just got a full time job and have come to the realization that I can’t store all of my saws in the apartment. It kills me to do this but I have to get rid of some saws. I probably won’t come across two of these again and I’ll most definitely regret this later on but I have no place to keep them (unless Dan or someone near by let’s me rent a part of there storage [emoji23]).

First up is a Homelite 26LCS. I got her to run when I zip tied some fuel lines on but the pull cord wire snapped. It will need one made unless you know where to find another. I’d highly recommend a carb kit or at least a carb clean. Everything else seems like she wants to dig into some wood

Sent from my iPhone using Tapatalk

 

[Bryan Barrow]

Next is the project that I took on from @usmcbuckwild at the NY GTG. I wish I had the time and money to spend on it and see it run but it’s not feasible at this point in my life. I’d at least like to see someone else get it going since I’m not able to. It’s a McCulloch 840. The muffler looks like a grenade went off in it, it missing the air filter, and lots of hardware. However, it’s very nice to look at. This is another one that sucks to let go but here it is

 

[Stump Shot]

@Sty57

 

[Bryan Barrow]

Number three is a Poulan 3700. I got this saw at a swap meet and haven’t even had time to do anything but clean it up a little. I’ve heard good things about the counter vibe series and I wanted to try it out but you know already that I can’t. So here’s the 3700

Sent from my iPhone using Tapatalk

 

[usmcbuckwild]

I’ll but the 840 back if you want. Save $$ on shipping

 

[Bryan Barrow]

Time to sell a hooskie. Husqvarna 455 Rancher. This is probably my best build yet. I put in a new piston, cylinder, rings, muffler, oil line, oil filter, and 20” 3/8 .050 bar and chain. I also cleaned the carb and had Russel Wicks give it a look to make sure it was ready to sell. This is a very clean saw.

Sent from my iPhone using Tapatalk

 

[Bryan Barrow]

I’ll but the 840 back if you want. Save $$ on shipping

I’ll send you a message


Sent from my iPhone using Tapatalk

 

[Bryan Barrow]

I just got news that I might have a storage area. If I do then I’ll have to take the 840 and the 26LCS down


Sent from my iPhone using Tapatalk

 

[paragonbuilder]

Bryan
Of course you can store any saws at my place. Not a problem at all.

 

[Bryan Barrow]

Bryan
Of course you can store any saws at my place. Not a problem at all.

Well. The 455 and the 3700 are still available. I’ll be keeping the 26LCS and the 840. Thank you Dan!


Sent from my iPhone using Tapatalk

 

[chipper1]

Glad you got a place to store some saws .
Did you use oem parts on the 455, how much are you looking to get for it.

 

[Bryan Barrow]

Glad you got a place to store some saws .
Did you use oem parts on the 455, how much are you looking to get for it.

Oem: muffler, oil line, oil filter

AM: piston, rings, cylinder

I have $150 into the saw so I’d like to get anything more than that


Sent from my iPhone using Tapatalk

 

[chipper1]

Oem: muffler, oil line, oil filter

AM: piston, rings, cylinder

I have $150 into the saw so I’d like to get anything more than that


Sent from my iPhone using Tapatalk

Thanks.
I know someone who may be interested.