SELLING Husqvarna saws, McCulloch parts, Mac 2 man Auger

[northwest saws]

Hello there everyone. Posted this on AS but thought I would try here as well. I've started spring cleaning a little early this year and would like to sell a few saws and parts to make some space. First is the husqvarna saws. I've got four L65's and one 140s. One of the L65's is a runner, two fire on a prime and the other is a parts saw that I haven't tried to fire in awhile. The 140s fired on a prime.
The Wright reciprocating saw is sold. As for the McCulloch parts I have a 4-30 carcass, a two man auger and a few 1-51 parts. I have a couple auger bits too but I'm going to have to do some searching to find them. I take paypal and am good with reg. goods n services or friends & family. Prices will be included with pictures. I would really like to clear all this stuff out though so if you think the price is high then make an offer....and no the 056 in the corner of the main pic is not for sale.

Sent from my SM-N970U using Tapatalk

 

[northwest saws]

L65 No.1 *Updated Complete and runs decent but has only 130psi compression. Oiler works, starter works, on/off switch works. One of the starter mounts is busted off. Would make for a good project. $75

 

[northwest saws]

L65 No.2 *Updated Very good physical condition. Missing a little paint on clutch cover and a little dirty though. Got it to fire on a prime, didn't try to run it off of the tank. Gas tank is nasty and will need a good cleaning. Carb most likely will need a kit put in. Has good compression at 152psi, piston also looks good from exhaust side. $60 obo.

Sent from my SM-N970U using Tapatalk

 

[northwest saws]

L65 No.3 Got it to fire off a prime but won't run off the tank. Most likely needs a kit put in the carb. A little dirty but in decent physical condition. Compression is poor and at the minimum needs a new set of rings. Saw is complete. $50 obo

Sent from my SM-N970U using Tapatalk

 

[northwest saws]

L65 No.4 When it had a starter I got it to fire off a prime. No longer has a starter, muffler or air filter cover. Choke plate is busted. Piston has some wear, compression seems poor. $35 obo

Sent from my SM-N970U using Tapatalk

 

[northwest saws]

140s Saw is mostly complete,, it might be missing a few screws. Needs a new pull cord and most likely a kit put in the carb plus fuel line and filter. Got this to fire on a prime. Compression seems decent. $50 obo

Sent from my SM-N970U using Tapatalk

 

[northwest saws]

1-51 handle bar is a little rusty but intact. 640 flywheel cover has a crack at the lower right corner, crankcase side cover also has a crack near the upper middle. 4-30 handlebar also a little dirty and a little rust but intact. Flywheel is missing one fin. Not sure if the coil works. Spike is rusty but intact. Shoot me a offer.

Sent from my SM-N970U using Tapatalk

 

[northwest saws]

4-30 carcass is pretty clean. The handle must have taken a hit at one point because it's been welded in two spots. Crank and rod look to be in great shape. Gears and clutch turn smoothly. Crankcase side cover has one tank mount that is busted. One tank mount on the clutch side is also busted. Make an offer.

Sent from my SM-N970U using Tapatalk

 

[northwest saws]

Mcculloch two man auger. The outside isn't in too bad of shape but does have a little rust. I couldn't get the gears to turn, it's siezed up pretty good. Pretty sure I have an auger bit or two somewhere here but I'll have to find em. Make an offer.

Sent from my SM-N970U using Tapatalk

 

[northwest saws]

Wright is sold but the husqvarna saws and mcculloch parts are still available. L65 posts no.1 and 2 updated. I found a bent throttle rod on the runner L65 which turned out to be the cause of the erratic running. Bent it back into proper position and the saw runs pretty decent now. Took compression readings on L65 no.1 and 2. Will get readings for the other three soon.

Sent from my SM-N970U using Tapatalk

Sent from my SM-N970U using Tapatalk

 

[Maintenance Chief]

@heimannm
Did you see the auger?

 

[heimannm]

I have an NOS gearbox in the display, but no augers to go with it.

Mark

 

[Mooselegs]

Would you have any L-65 Saws or Parts Remaining

 

[Ketchup]

Would you have any L-65 Saws or Parts Remaining

I do if he doesn’t. PM me if you don’t hear from the OP.