SOLD Husqvarna 395xp (no longer for sale)

[GoBigBlue1984]

Selling one of my 395's. Cosmetically it's not a Beauty queen but it runs and cuts well. OEM top end. Installed new caber top ring. Nachi bearings, AM seals from Dave. Cut .025 from squish band and .045 from the base. Squish is .020 with gasket. 205 compression, that'll go up some.
Starter cover has missing ribs (4-5). Inner dog bottom bolt hole will need to be easy outed. Missing the set screw that adjusts the oiler.
Asking $450 shipped to lower 48 PHO
I'll post a video a little later of some cuts from today.

 

[GoBigBlue1984]

The lower dog where the bolt has been broken off.

 

[GoBigBlue1984]

This saw came from our local husqvarna dealer as a warranty return. Ben @idiotwithasaw can vouch for this. He actually bought it from them and I acquired it from him via trade.
I should've included this information in my original post, didn't give it much thought. I'm Selling this saw to fund some other projects.

 

[GoBigBlue1984]

 

[idiotwithasaw]

Yeah, i dug that thing out of a pile and brett did wonders with it. he has been using it almost daily to cut up firewood with no troubles. It's a strong saw if I needed it I would be happy to have it. Buy with confidence this was fixed right from the ground up.

 

[Jon1212]

Less than $5.00 per cc on a rebuilt Pro Saw?......

This is one of the best deals I've seen for a Milling or large bucking saw.

 

[idiotwithasaw]

This would make a perfect milling saw for someone wanting to get into it.

 

[mdavlee]

It sure would. That's my pick for a milling saw for under 42" bar. Just be sure to lock tite the muffler bolts and check the top cover ones every day when milling.

 

[angelo c]

must resist saw.
must resist saw....
nobody likes "husky" saw anyway....I hate husky saw( why do I have so many ?)
keep on hatin !!!

that's a lot of saw for the money.

wish I wasn't tractor shopping.

 

[CR500]

must resist saw.
must resist saw....
nobody likes "husky" saw anyway....I hate husky saw( why do I have so many ?)
keep on hatin !!!

that's a lot of saw for the money.

wish I wasn't tractor shopping.

What tractor you looking for?

Sent from my non internal combustion device.

 

[CR500]

must resist saw.
must resist saw....
nobody likes "husky" saw anyway....I hate husky saw( why do I have so many ?)
keep on hatin !!!

that's a lot of saw for the money.

wish I wasn't tractor shopping.

What tractor you looking for?

Bump for a hell of a deal!!!

Sent from my non internal combustion device.

 

[GoBigBlue1984]

If this thing doesn't sell in the next couple days I'll pull it and raise transfers and try to get some desired numbers. Post some video after that. Stock was 101/129/77. Won't have time to do it till then, so I'll keep it up for a while longer. I feel there's much to be had with this one.

 

[Jon1212]

If this thing doesn't sell in the next couple days I'll pull it and raise transfers and try to get some desired numbers. Post some video after that. Stock was 101/129/77. Won't have time to do it till then, so I'll keep it up for a while longer. I feel there's much to be had with this one.

I really like the one I have, stock. It does everything I need it to. I generally run a 32" 3/8 bar on mine, and it doesn't even slow down when I lean on it, and it burns fuel more economically than my "spicy" 372.

 

[Bigblock]

nice saw

 

[angelo c]

What tractor you looking for?

Sent from my non internal combustion device.

the "holy grail" of tractors of course...
30 hp
TLB
4wd
preferably Kubota
(and everything else I don't need just to load my dump truck with firewood)
oh wait....the magic word too... "CHEAP".....

 

[exSW]

What tractor you looking for?.

Cab,air,heat,three hydraulic remotes,90-120 hp,front assist nice but not a deal killer,under 5000 hrs and preferred in Red. Also why this saw isn't going to be mine.

 

[CR500]

the "holy grail" of tractors of course...
30 hp
TLB
4wd
preferably Kubota
(and everything else I don't need just to load my dump truck with firewood)
oh wait....the magic word too... "CHEAP".....

Have a 3046 on our lot lol Cab and AC.... Has the recent the Harness update by yours truly. ( Could not even tell I pulled the cab)

Cab,air,heat,three hydraulic remotes,90-120 hp,front assist nice but not a deal killer,under 5000 hrs and preferred in Red. Also why this saw isn't going to be mine.

7630 be sufficient lol

 

[exSW]

Have a 3046 on our lot lol Cab and AC.... Has the recent the Harness update by yours truly. ( Could not even tell I pulled the cab)


7630 be sufficient lol

No green 7 series Deere if you're a tech you know why. 6430 premium would be my choice in green but is out of my price range. Late 4430 would be ideal but I can't stand Soundgard cabs.

 

[angelo c]

Have a 3046 on our lot lol Cab and AC.... Has the recent the Harness update by yours truly. ( Could not even tell I pulled the cab)


7630 be sufficient lol

Yea, I dont really understand the numerology behind the green ones...kinda like Jonserreds to me....I just don't get it.
All I know is some are made by "parts unknown" but pricing says "good ol 'Mericans "

 

[exSW]

3046 be a Yanmar wouldn't it? Neighbor has a 4xxx sweet little tractor. Much preferred by the hired help to the 5305.