High Quality Chainsaw Bars Husqvarna Toys Hockfire Saws

ZERO's latest activity

  • ZERO
    ZERO reacted to huskihl's post in the thread 500i E clip removal with Like Like.
    Lay them on their side and lightly tap the washer down with a hammer. Creates enough clearance that the eclip pops right off. They get...
  • ZERO
    ZERO reacted to singinwoodwackr's post in the thread 500i E clip removal with Like Like.
    Ah, welcome to Husky land, lol I remember denting my neighbor’s garage door…across the street once 🤣
  • ZERO
    ZERO reacted to singinwoodwackr's post in the thread 500i E clip removal with Like Like.
    Then that clip was done in the first place and neither washer would have prevented the failure.
  • ZERO
    ZERO reacted to bogieboy's post in the thread 500i E clip removal with Like Like.
    It will work.... thats coming from a certified stihl tech.... have done may hundreds of them that way....
  • ZERO
    ZERO reacted to IffykidMn's post in the thread 500i E clip removal with Like Like.
    Did not use a carb screwdriver but did use a narrow screwdriver that fit the width of the clip slot and pried it off no fuss not sure if...
  • ZERO
    ZERO reacted to bogieboy's post in the thread 500i E clip removal with Like Like.
    Just had that happen to me a few weeks ago when i was fixing carb issues on my old 020ave, apparently i didnt get the nut on the clutch...
  • ZERO
    ZERO reacted to Gary Courtney's post in the thread 500i E clip removal with Like Like.
    Was working on a 262 w/o clutch cover and revved it up and clutch came off and went 2 blocks down the street before coming to rest
  • ZERO
    ZERO reacted to bogieboy's post in the thread 500i E clip removal with Like Like.
    Right up til ypu are noodling that one big log, and the clip, washer, and driver go flying into the abyss that is the noodle/sawdust...
  • ZERO
    ZERO reacted to singinwoodwackr's post in the thread 500i E clip removal with Like Like.
    Dremel with cut-off wheel to the clip; throw the machined washer, and clip parts, away. Replace with old style. Quick, satisfying, no...
  • ZERO
    ZERO reacted to bogieboy's post in the thread 500i E clip removal with Like Like.
    For the newer milled style washer, best thing i have found for popping them off is a stihl carb screwdriver... get it in one of the...
  • ZERO
    ZERO reacted to sawmikaze's post in the thread 500i E clip removal with Like Like.
    Totally different scenario.
  • ZERO
    ZERO reacted to sawmikaze's post in the thread 500i E clip removal with Like Like.
    Not that I'm aware of, but some of these guys are pretty crafty. Echo makes a red armor grease that I use for the needle bearing.
  • ZERO
    ZERO reacted to fdhamlin's post in the thread 500i E clip removal with Like Like.
    Can't say about an 500i but on my MS250 I replaced the e-clip with an O-ring. It is holding up just fine and it is dead simple.
  • ZERO
    ZERO reacted to IffykidMn's post in the thread 500i E clip removal with Like Like.
    Curious if anyone has tried modifying a set of pliers in a similar fashion to those for roller chain master link pliers with one jaw...
  • ZERO
    ZERO reacted to sawmikaze's post in the thread 500i E clip removal with Like Like.
    Isn’t it funny how you can try to get that e-clip off the same way for 15 minutes and then all of a sudden it comes off even though you...
Show older items
Top