upstateamish's latest activity
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".Running echo red armor @ 40:1 Piston / cylinder look decent. wiped things down, tweaked the carb slightly and it doesn't seem to be...
-
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".3rd run, getting it tuned in a bit more, I think I've almost go it dialed in so it will rev and won't die after sitting at idle for a...
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".ok, I believe I found the source of that knock. I sheared the timing key on the flywheel when the lock washer came loose. I happen to...
-
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".Alright. after searching through the bins for a bunch of random parts along the way... Got it together. I have a couple parts that still...
-
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".Parts arrived over my lunch break! I installed the new seal and it is now holding pressure/vaccuum. So I started pulling the rest of...
-
-
Uupstateamish reacted to Ketchup's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with
Like.
Looking at 385/390, there’s no bushing. The oil gear just rides on the pump. Seems like that would overheat the gear, but it would... -
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".Yeah, I don't have an actual 385/390 to reference but from what I can tell in my research they changed their bearing style to move to an...
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".Me too! If it works, the next prototype will need some additonal case trenching on the clutch side to case match the transfers. And...
-
Uupstateamish reacted to Ketchup's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
Great work! Very excited to see a 95cc 372.
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".Ok, some forward progress, I have the short block together (well, as far as I can get tonight) - new crankshaft bushing made - piston...
-
-
Uupstateamish reacted to Ketchup's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
My first try was 82/100/122. It’s apart right now and I bumped to 82/98/122. I epoxied the transfers but didn’t break through. Once...
-
Uupstateamish reacted to Outback's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
If that's the case I would say that less is more as regards the intake timing. Keep that primary compression up as high as you can.
-
USo I checked the compression on the 395 as I bought it used. 155psi so not to bad. Put a new filter on it. Plug looked good. I bought it...
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".Agreed on that amount of blowdown it seems like a lot. But I was reading somewhere (maybe this thread?) that this particular bigbore kit...
-
Uupstateamish reacted to Powerstroke Cowboy's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
Looking good! Glad to see it's coming along as well as it is. All the little (sometimes big) hurdles is what makes these builds...
