upstateamish's latest activity
-
Uupstateamish reacted to EFSM's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with
Like.
Why are the new saws going short stroke? That makes sense on a 4 stroke (more room for valves) but a long stroke on a 2 stroke engine... -
Uupstateamish reacted to Jake Dykstra's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
Not planning on using the 372 platform for the 592 build. Going to use the 572 platform. The 564 looks interesting for what it is but...
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".Was away for the weekend but sounds like there's still a bit of interest in this project! Had a good conversation last night with my...
-
Uupstateamish reacted to Jake Dykstra's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
Thats exactly whats on my bench next. 592 should be here next week! I was thinking of starting with a 585 if I can't get enough weight...
-
Uupstateamish reacted to Ketchup's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
592 jug on a 572?
-
Uupstateamish reacted to Ketchup's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
You get more piston options and that may solve the wrist pin difficulties, but you only gain 12cc instead of 24. At that point you’re...
-
Uupstateamish reacted to Ketchup's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
It’s a ported 94.4cc saw that weighs 16.6lbs. Nothing else comes close to that.
-
Uupstateamish reacted to Jake Dykstra's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
That would be worth the work!
-
Uupstateamish reacted to Jake Dykstra's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
My 390 pho weights 19.6 lbs topped off.
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".prototype 2 (pho with a 572 clutch cover, half wrap handle) weighs - 16.6lbs topped off with gas/oil
-
-
Uupstateamish replied to the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube".Hey hey, it's been a minute. Sorry for leaving everyone hanging. . . I got pulled away on to some vehicle projects and then life got in...
-
Uupstateamish reacted to Ketchup's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
I took a lot of weight off. Cut the crown, slabbed the sides, cut windows, ground out a lot from inside. That piston had the original...
-
Uupstateamish reacted to Jake Dykstra's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
Ah shoot. That sucks. I had a 353 that I put lots of time into as well. It ripped for a 50cc saw. Lost a Cclip and wasted the piston and...
-
Uupstateamish reacted to Ketchup's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
Mine is all torn apart in a box under my bench. I think it ingested a piece of exhaust gasket. I put a lot of work into that piston...
-
Uupstateamish reacted to davidwyby's post in the thread Hybrid clonesaw 365 with a 390 topend - aka the "86'r from youtube" with Like.
Take the V6 out of a truck and put a big block in. Negligible. I’m sure the weight is closer to the small saw weight than the big saw...
