SawAddictedFarmer's latest activity
-
SSawAddictedFarmer reacted to jacktheripper's post in the thread Not so pros 4 new and without politics or drama with
Like.
Got a new boot and storm collar installed around my chimney pipe today. I’ve been getting a lot done on this two week paternity leave -
SGot my base and squish cut and upper transfers raised with my friend Caleb today for the 272xp. Just need to do exhaust and intake!
-
SSawAddictedFarmer reacted to Merkava_4's post in the thread STIHL Clutch Drum Fan Housing Assembly with Like.
I bought this clutch drum off of eBay on 05/27/2025. Already the bearings feels rough and are making noise. Are the bearings...
-
SSawAddictedFarmer reacted to jacob j.'s post in the thread STIHL Clutch Drum Fan Housing Assembly with Like.
There should be a standard bearing can you press in there. You'll need to remove the old bearing and get the measurements on it and then...
-
SSawAddictedFarmer reacted to jacktheripper's post in the thread Preparing to port first saw - which one, and what method? with Like.
Mastermind was at least two seconds faster in the same wood. MOFO 440 hybrid was almost four seconds faster.
-
SSawAddictedFarmer reacted to Sloughfoot's post in the thread Preparing to port first saw - which one, and what method? with Like.
Iirc 102 22 78 is what he's said his target numbers are for 044s.
-
SSawAddictedFarmer reacted to jacktheripper's post in the thread Preparing to port first saw - which one, and what method? with Like.
044 is 50mmx36mm 272 is 52mmx34mm I wonder how the bore/stroke ratio comes into play with blowdown. My 266xp that I ported without...
-
SSawAddictedFarmer reacted to Sloughfoot's post in the thread Preparing to port first saw - which one, and what method? with Like.
Yeh, No expert but I'd think the shorter stroke would call for less blowdown. I believe popular opinion for an 044 is 20 blowdown...
-
SSawAddictedFarmer reacted to jacktheripper's post in the thread Preparing to port first saw - which one, and what method? with Like.
Didn’t measure compression, but it definitely feels stronger. I put a ring in it less than a year ago, and it honestly hasn’t been run...
-
SSawAddictedFarmer reacted to huskihl's post in the thread Preparing to port first saw - which one, and what method? with Like.
A couple more degrees of blow down usually makes it a little bit more forgiving, but won’t hold RPMs as well in a simple down cut. You...
-
SSawAddictedFarmer reacted to jacktheripper's post in the thread Preparing to port first saw - which one, and what method? with Like.
This seems contradictory to this: What do you mean @huskihl? Thanks for your replies!
-
SSawAddictedFarmer reacted to Sloughfoot's post in the thread Preparing to port first saw - which one, and what method? with Like.
Had to reread it a time or 5, myself. I believe what he's getting at is a higher blowdown number (lower transfer roof) won't cut at as...
-
SSawAddictedFarmer reacted to huskihl's post in the thread Preparing to port first saw - which one, and what method? with Like.
Not contradictory, just that I’m not relaying what I’m trying to say very well. Raising the transfers and raising the exhaust will both...
-
SSawAddictedFarmer reacted to huskihl's post in the thread Preparing to port first saw - which one, and what method? with Like.
But to make certain we’re on the same page, blow down is the distance from when the exhaust opens to when the transfers open. It gets...
-
SCraigslist and marketplace people are insane. I gave a guy an address to check distance Friday morning. Checked my messages Friday...
