High Quality Chainsaw Bars Husqvarna Toys Hockfire Saws

Duane(Pa)'s latest activity

  • Duane(Pa)
    Duane(Pa) reacted to PA Dan's post in the thread RIP Saw 500i with Like Like.
    A few years back i had thoughts of getting a 500i. @huskihl brought one to the PA GTG for another PA guy. I asked if I could run it...
  • Duane(Pa)
    Duane(Pa) replied to the thread Definitive Dave...Discussion.
    Dee Leet it...
  • Duane(Pa)
    Duane(Pa) reacted to Jay Hansen's post in the thread SELLING Homelite Super EZ with Like Like.
    I actually have a fair amount of respect for the Super EZ. It was well built, very light for the era, and it was equipped with full...
  • Duane(Pa)
    Duane(Pa) reacted to tree monkey's post in the thread Carb difference with Like Like.
    not much, 19 would be pre epa. both will work fine on a stock saw. if your going to port it i would use a16 from a 460
  • Duane(Pa)
    Duane(Pa) replied to the thread Dominator oil.
    Winter blend for sleds, summer blend for boats. Never saw mix fuel except at marinas here in pencil tucky. PS I will have convulsions...
  • Duane(Pa)
    Duane(Pa) replied to the thread Dominator oil.
    Amsoil marches to a different beat in many ways. Their response is probably something along the lines of "consider the results of the...
  • Duane(Pa)
    Duane(Pa) replied to the thread Stale fuel issues.
    M Tronic? Sounds like might knead a solenoid…
  • Duane(Pa)
    Duane(Pa) replied to the thread Ms362 exhaust leak..
    Thanks fellers. Sorry too about derail...shirt happens
  • Duane(Pa)
    Duane(Pa) reacted to lehman live edge slab's post in the thread Ms362 exhaust leak. with Like Like.
    Local hardware store sells an insert in there generic plastic divided bins, inserts are like 75 cents to a couple dollars depending on...
  • Duane(Pa)
    Duane(Pa) reacted to timg's post in the thread Ms362 exhaust leak. with Like Like.
    @Duane(Pa) I've had good luck with thin wall keenserts from McMaster Carr. Drill super slow and straight with lube on the initial cut. I...
  • Duane(Pa)
    Duane(Pa) reacted to hacskaroly's post in the thread Ms362 exhaust leak. with Like Like.
    Yeah, I looked into timeserts, ended up going with a helicoil it off of Amazon for another job. They worked well for holding cylinder...
  • Duane(Pa)
    Duane(Pa) reacted to Stump Shot's post in the thread Ms362 exhaust leak. with Like Like.
    On some cylinders from Husqvarna(like the 390?), Helicoils were already installed from new. This should be fine if installed correctly...
  • Duane(Pa)
    Duane(Pa) replied to the thread Ms362 exhaust leak..
    Threads in jug at exhaust flange. I think it’s 5mm. Watched video of timesert brand. Tools are expensive inserts are reasonable…
  • Duane(Pa)
    Duane(Pa) reacted to legdelimber's post in the thread Ms362 exhaust leak. with Wow Wow.
    Should I admit to having put muffler screws on a hot stove element, before screwing them in? Yes pliers and a couple of room temp...
  • Duane(Pa)
    Duane(Pa) reacted to EFSM's post in the thread Ms362 exhaust leak. with Like Like.
    Use a Helicoil repair of your choice if in aluminum. You will end up with stronger threads than original.
Show older items
Top