Recent content by AVB

It is not having some ads that is the problem but sites that 100+ Ads that my Adblocker stops if it wasn't for NoScript blocking the script that deliver them. That site is basically useless if it weren't for these two apps. As for the Maple Syrup it demands if US or Canadian. Those darn...

What are Ads? I haven't seen any in yrs here but that may be because I run an Ad blocker along with a script blocker. i only allows the necessary scripts needed to get a site to work. The only ad script that sneak in at times and that one gets caught by the anti-spyware software that I run...

It will produce a lot carbon and clog the spark arrestor for one thing. Note has a speed limiter set at 12,500 rpm [10,500 rpm if RC version] so these rev a lot higher. To properly adjust the carb you need a tach and then follow the following instructions.

I have a problem with both the Park City and Decherd. They just get thru their head that I can't received text messages because I don't have a cell phone and I have repeatedly told them so. This causes my parts sit for weeks at a time.

Yes apparently Stihl decided to more of a pain by changing the hexagon to an octagon to force to have a dealer only to work on our and our customers equipment. The octagon tool is PN 5910 890 2314. (for anyone else needing the PN) I even had one dealer just this Fall to demand to see my DL in...

Well most of us have enough common sense to know you don't go at it the proverb-able sledge hammer force. I use a 2# brass hammer. You use no more force than necessary and not get in big hurry. I have yet to damage a crank, bearing, or seal. Although seals are usually the reason I pull a...

Well it does gives the user less of a chance damaging flywheel fins miss lick and especially in a recessed holes like this Stihl has. Not all of us have prefect aim. An example is the bathroom fixture that gets wet all over the place. Note the external threads on the Stihl tool are 1.5mm...

Welcome to metal tariffs if in the USA. My lord all you need most times is a Flywheel Knocker. It is thread on the crankshaft end at the flywheel all the way and then backed off one to two turns. Then hit the end with a soft hammer to bump the flywheel off the taper. Usually only take one hit...

Any particular reason why a M8-1.00 flywheel knocker won't dismount the flywheel? BTW I do have the 1110 890 4500 in the shop but can't open door due to ICE stopping me. Oh well maybe in a week I can open the door. But you should be give up some beer and cancer sticks for one without someone...

Kinda looks like Everett is no where close (ei out in the sticks) to any major town. Where I am here in TN every large town is at 25 mole hills away. It looks worst on the map for Everette, PA. This makes hard to get anything done including medical care. But I would not give up the country life...

Traprunner, Sorry for the delayed response your post #15. I wasn't ignoring your post, it just got buried in the replies. But I was going thru all the replies this morning when I saw it. Tnx for the image and Oregon series numbers. The only problem is that is a 0.043 and appears they don't...

Yes they are Poulans as Husqvarna owns Poulans. It just the real old Poulans are part of Husqvarna. For parts and labor you can't be hard nosed about billing as long you make a profit. I bill on a pro-rated rate on the cheaper saws. This brings a lot more profitable work like the ZTRs. Just...

530031112 fits Husqvarna 136, 141, 36, 41 and Poulan 2035, 2775, 4016, 4218. And own a 4218 with the NCC cylinder. 530021116 fits Craftsman 2700, 2800 3000, 3000CB, 3100, 3300, 3350, 3450, 3500, 3600, Poulan Pro PP285, PP305, PP330, PP335, PP336, PP336C, PP365, PP365C, PP5020AV, 1975LE, 2025...

Hopefully you two versions of this Poulan clutch tool. One has the pins slightly farther apart which why I had order the second one.

Very nice beefy tools. I just wish the customers would learn to use the proper tools and the correct hardware as that would eliminate a lot of our hardware problems. Tried this tool with a scrench but failed as things just went sideways so I had impact socket done. Beside I can now use a pull...