67L36Driver's latest activity
-
67L36Driver reacted to Hedgerow's post in the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread? with
Like.
Gotta fold that intake boot in on itself then wiggle the *s-word out of it.. That cover seals into its base and is most likely just stuck... -
67L36Driver replied to the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?.Solved the chain problem on the Deere. Change the bar tip to 3/8”. 😉
-
67L36Driver replied to the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?.Hedgerow: What is the secret handshake to get the top cover off? Got the usual three screws out but the end by the rear handle acts...
-
-
67L36Driver reacted to Fishnuts2's post in the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread? with Like.
I've got a couple of those. Not exactly the best design for a starter, that's for sure. Nice little saws otherwise.
-
67L36Driver replied to the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?.Most miserable saw starter ever. Small and deep housing, strange pulley(difficult) end termination and auto decomp to boot. It took...
-
-
67L36Driver reacted to Fishnuts2's post in the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread? with Like.
And the neat part is that it's all free!
-
67L36Driver reacted to Hedgerow's post in the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread? with Like.
It’ll never need another chain. I only used it once, ran the fuel out and it sits next to the David Bradley.
-
67L36Driver replied to the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?.That was a 17, AKA SL or PL 4 Remington. IIRC, I put a 16” x .404 on it. Good luck if you have to swap chains. 😈💀
-
67L36Driver replied to the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?.Yes, I sold mine and inherited Jim Roger’s 655.
-
67L36Driver reacted to sawnami's post in the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread? with Like.
You've got me there, Thomas. It's supposed to be art. I remember that he brought these stools to the first GTG. The top was on a ball...
-
67L36Driver replied to the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?.I may have a deal for you. 🤥 Wait. 🤔. But do you have a JD 23?
-
67L36Driver replied to the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?.Maybe this is a Windsor bar. Slot is a wiggle over 3/8”. Bar studs have shoulder. 5/16” shank. Rim sprocket so the real problem...
-
-
67L36Driver replied to the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?.To verify, upload a panoramic picture and see. 🤔 Also: The PP bar was a random one Curt had hanging in his shop that happened to be the...
-
67L36Driver replied to the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?.I’m haveing the same problem. 😑 Previously mentioned John Deere CS 81 (Eefco). Bar is 30-32 ish .404 x .058 gauge (). 404 x 058 is...
-
-
67L36Driver reacted to sawnami's post in the thread how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread? with Like.
Good morning! One of my inspection visits last week took me to John Taliaferro's shop. John had the first GTG that I went to. It was...
