What's on your bench?

[Jon1212]

Sucky part about these Huskies is that there are no long small mount bars. I wanted to load the saw up good today with a 32.

@drf256 that's a 32" K095 on top. I have a couple of them, and I know where to get a dozen more.

@Jon1212

Thanks for remembering.

 

[StephK87]

Just another 572xp (390xp was for size comparison), now I'm waiting for another MS462 for stock/ported battle. [emoji16]

 

[Sty57]

Good way to bend or break a crank, ask how i know

I can see where it could happen.
But I just rev it up enough to engage the clutch. Then as the chain is spinning down I trip the break.
I can't see how that would be much different than running the saw and the brake trips on it's own.

 

[Sty57]

Ready to do work, so the worksaws are out.

View attachment 133505 View attachment 133506 View attachment 133507 View attachment 133508

I see earplugs and glasses......but where are your chaps?
I've had 2 really close calls cutting firewood. I'll never go in the woods without them anymore.

 

[ranchdadmike]

8 pin and a 20. First 198 carbed saw ive done. Wants to 4 stroke to the moon

Initial tune in vid piss revving was 15600. Turned down to 14200 and then 13800.

Tried to vid rpm in cut. Was holding between 10500 and 12k in cut.

Bye bye -87s?!

 

[Czed]

I can see where it could happen.
But I just rev it up enough to engage the clutch. Then as the chain is spinning down I trip the break.
I can't see how that would be much different than running the saw and the brake trips on it's own.

I've had a few am clutch covers
They worked fine just trying them out
Was deceiving
They would trip wfo
Suprised i never broke a crank

 

[MustangMike]

Going from 7 pin to 8 pin is a 14.3% difference (1 / 7). Increase in speed, decrease in torque.

8 to 9 is only a 12.5% difference.

Just simple grade school math.

 

[Tor R]

Ummm, some pricey bastards...


Probleby the biggest loss I've had on a saw, bearings, ring, bellow, partition, flange and the list go on.. dunno why they are populare!

 

[drf256]

 

[drf256]

Bye bye -87s?!

Exactly

 

[usmcbuckwild]

WTF?!?!? Hahaha

 

[Duane(Pa)]

The 7 pin is diameter of 35 MM
The 8 pin is diameter of 40 MM

Let's use a 372 XT as an example. It's rated (per Husky) at 3.8 N*M of torque

The force exerted (Newtons) would be 3.8 N*M divided by the radius of the rim.

3.8 / .0175 = 217 Newtons of force exerted on the chain
3.8 / .020 = 190 Newtons of force exerted on the chain

That's a 12.4 % decrease in force exerted on the chain. However, the chain is spinning faster by about the same ratio, so it's all a balance.

I'll take the Newtons...I know where to find chain speed

 

[usmcbuckwild]

I like torque. Torque makes me smile

 

[Sty57]

I'll take the Newtons...I know where to find chain speed

Mmmmm Fig Newton.......

 

[Duane(Pa)]

Ft. Lbs. FTW newtons are cookies

 

[Sty57]

Ft. Lbs. FTW newtons are cookies

.

 

[Bigmac]

That hurt to watch...ouch

 

[Onan18]

I like torque. Torque makes me smile

"Horsepower is how fast you are going when you hit the wall, Torque is how far you take the wall with you."

 

[MustangMike]

That's like:

I'm not afraid to go fast … it's the crash + burn that scares me!

 

[Roadfxr]

"Horsepower is how fast you are going when you hit the wall, Torque is how far you take the wall with you."

QTLA