What's on your bench?

[Mkinslow]

Managed to get its first run in before family stuff. Around two turns out on high side, 1.5 on low side. I gotta get more familiar tuning ported saws. Plug was dry? after 6-7 cuts. Definitely stronger than stock though.

Sent from my SM-G892A using Tapatalk

Here's the plug after those 6-7 cuts

Sent from my SM-G892A using Tapatalk

 

[redline4]

View attachment 172741

Is it getting Mo Fo'd?

 

[David Young]

H51 intake

 

[MG porting]

Here's the plug after those 6-7 cuts

Sent from my SM-G892A using Tapatalk

Give it a little bit more fuel just a touch and she'll live a happy life.

 

[drf256]

Is it getting Mo Fo'd?

More like it’s being a Mofo. Ported. Having MT problems.

 

[Mkinslow]

Give it a little bit more fuel just a touch and she'll live a happy life.

Thank you sir, that's about what I was thinking myself. Wanted to se what yall thought

Sent from my SM-G892A using Tapatalk

 

[Graf]

New carb for Active 39.39 and roars again... While it lasts!

 

[Sleeper]

H51 intake

What heli coil kit size do you use for the partition plate? What size and thread carb bolts do you use?

Got a bunch of these series Huskies that will be made into runners. Don't want them to come back, so I will do it right.

 

[David Young]

What heli coil kit size do you use for the partition plate? What size and thread carb bolts do you use?

Got a bunch of these series Huskies that will be made into runners. Don't want them to come back, so I will do it right.

M5x.8 helicoil. Use a m5x45 mm socket head bolt. I do this even if they are not stripped yet

 

[tickbitintn]

People usually overtighten those, even if they are not stripped the threads can be pulled some and weakened without looking bad or damaged.
Simple and economical fix.

Sent from my XT1635-01 using Tapatalk

 

[MG porting]

Thank you sir, that's about what I was thinking myself. Wanted to se what yall thought

Sent from my SM-G892A using Tapatalk

You're welcome.

 

[J. Loe]

Photos to follow, but I’ve got this 10mm 044 slantfin on the bench that needs all the magnesium replaced.

CrankCase, starter and Clutch cover.

As well as seals, bearings, air filter....
There’s actually more to the list.

Fellow who owns the saw has a budget.
Of course.

Are there aftermarket cases for these?
for example

How’s that grab you ope?

The saw was definitely struck by or dropped on and I’m not sure the crank is 100% straight but the piston and cylinder seem to be in good shape.
All the bits are there and cleaned up pretty well.

Case is garb.

 

[dustinwilt68]

Might be cheaper to use the OEM parts on AM cases and crank, built on 440 platform

 

[J. Loe]

Might be cheaper to use the OEM parts on AM cases and crank, built on 440 platform

Thank you sir!

So that’s reusing the cylinder, getting a new oem piston kit on that am case assembly I linked to?

Can I keep the AM bearings, seals?

 

[dustinwilt68]

I would use the AM seals.and bearings, haven't heard much issues with them, for the piston order a meteor and save your self some $. Run the OEM cylinder, circlips and bearing. I always like OEM carbs too. Make sure and wash that cases out first before assembly with mix, flush the AM bearings also

 

[J. Loe]

Sweeet!

Game On!

 

[usmcbuckwild]

I have a 365 special on the bench getting an overhaul; new bearings, new crank, new seals, new ported OEM OE cyl, not sure if OEM piston or Meteor, Cabers, RWJ4 and a muff mod. I forgot to take pics before coming inside.

I’ll send pics in the morning!

 

[cus_deluxe]

Thank you sir, that's about what I was thinking myself. Wanted to se what yall thought

Sent from my SM-G892A using Tapatalk

that saw was fourstroking most of the way through the first cut, and a little at the end of the second. its got plenty of fuel already.

 

[dustinwilt68]

I have a 365 special on the bench getting an overhaul; new bearings, new crank, new seals, new ported OEM OE cyl, not sure if OEM piston or Meteor, Cabers, RWJ4 and a muff mod. I forgot to take pics before coming inside.

I’ll send pics in the morning!

Looking forward to this one!

 

[Mkinslow]

that saw was fourstroking most of the way through the first cut, and a little at the end of the second. its got plenty of fuel already.

Thanks. Yeah I've watched that video many more times and keep listening to it. I can hear it, but at first i thought it was rev-limiting,but then I remembered that saw has the black coil so....

Sent from my SM-G892A using Tapatalk