What's on your bench?

[Gary Courtney]

The 660 came up really well Gary nice job

Thanks Todd. How you be?

 

[merc_man]

Got a little poulan oops i mean husky 240 on the bench tor in a million peaces just to get the carb off and put new kit in. Heck of a setup ther lol.
I was running crappy and no carb adjustment made any difference. Put.kit in and seemed good for the 30 seconds i had it.running. gotta wait for momma bear to wake up so i can tune and test or.maybe throw in the garbage. Who knows lol.
My BIL baught it as non runner for 20 bucks. Only ran couple times. Sat on shelf and wont run. Tipicle home owner saw lol.

Sent from my SM-G950W using Tapatalk

 

[sawnami]

Mall 2MG

Sent from my SM-N950U using Tapatalk

 

[Cut4fun]

Big Thank you goes out to Scott Kunz aka @tree monkey

His video helped me trouble shoot and rebuild this 199 right for a 2159 non runner that came in. Drilled the hole and tan check valve side.
Came in with blue and gaskets out of order on other side.

Not a bad 35 saw low hr saw. He has little more then that in it now.

I think he is going to flip it later on. He runs a 260 441. Want me to ask what he will want for it?

 

[Johnmn]

Big Thank you goes out to Scott Kunz aka @tree monkey

His video helped me trouble shoot and rebuild this 199 right for a 2159 non runner that came in. Drilled the hole and tan check valve side.
Came in with blue and gaskets out of order on other side.

Not a bad 35 saw low hr saw. He has little more then that in it now.

I think he is going to flip it later on. He runs a 260 441. Want me to ask what he will want for it?





View attachment 165992 View attachment 165993 View attachment 165994 View attachment 165995 View attachment 165996

Yes! Let me know

 

[beaglebriar]

Big Thank you goes out to Scott Kunz aka @tree monkey

His video helped me trouble shoot and rebuild this 199 right for a 2159 non runner that came in. Drilled the hole and tan check valve side.
Came in with blue and gaskets out of order on other side.

Not a bad 35 saw low hr saw. He has little more then that in it now.

I think he is going to flip it later on. He runs a 260 441. Want me to ask what he will want for it?





View attachment 165992 View attachment 165993 View attachment 165994 View attachment 165995 View attachment 165996

That's a clean one, awesome saws.

 

[redlight066]

Not even lunchtime and I’m about cross-eyed. Halfway there though....

 

[Dub11]

View attachment 166182 Not even lunchtime and I’m about cross-eyed. Halfway there though....

Tell your boss man to get one of these.
http://opeforum.com/threads/temco-auto-sharpener-user-review-thread.15293/

We need to know how much about can take.

 

[redlight066]

I've been watching that thread. Pretty neat little machine

 

[Dub11]

I've been watching that thread. Pretty neat little machine

It is but I wanna know how many grinds it can kick out before mayhem ensues.

 

[Cut4fun]

Yes! Let me know

He picked it up just a bit ago. He said 350 would buy it.

Still has the plastic intake clamp but is tight. Front of cylinder through plug hole looked new still.
I warned him about it and what to watch for.

 

[Cut4fun]

After I read that one guy got that chain deal and it started sharpening wrong side wrong way.

Reading this is alittle scary.

Somebody on AS said = (I bought one of these and received it last week. It works well except when it ground the wrong way on a tooth for no apparent reason and ruined the tooth. Good thing I was standing there and could stop it from continuing. Hopefully this was a fluke and doesn't happen again. Now I need to get out and dull a couple chains and try it again.)

 

[MG porting]

View attachment 166182 Not even lunchtime and I’m about cross-eyed. Halfway there though....

Lol. Did that last month 60 chains sharpened them all buy hand I told them it would be last time I do that. Lol I'm sure you can figure out why I would say that.

 

[redlight066]

He's a good customer. So I do it for him. Not the best way to make a dollar, but for him I don't mind. Boy, by the time I was done with 12 chains. (half of them were 36 and 41 full comp) I was definitely ready to work on a couple of saws. That Silvey 510 in the pic has been a work horse. Bought it on ebay about 10-15 years ago. I'm almost ashamed to admit what I paid for it. They hadn't got so collectible yet.......$250 including shipping. It's nice Madsens still has a few replacement parts for it. Bought a handful of parts for it last year. Should be good to go for a while.
Rich

 

[Cut4fun]

Why I got a USG for doing other folks chains. I hate when the one guy drops off the 44"to 60" chains. I just want to . I hate doing chains as it is just repetition.

Sold my early silvey swing arm square grinder with stand last year for 550 when I listed it on chainsaw repair. Didnt last 5mins.

 

[Stihl working Hard]

Thanks Todd. How you be?

All is well this side of the pond my friend

 

[460 magnum]

Got a little poulan oops i mean husky 240 on the bench tor in a million peaces just to get the carb off and put new kit in. Heck of a setup ther lol.
I was running crappy and no carb adjustment made any difference. Put.kit in and seemed good for the 30 seconds i had it.running. gotta wait for momma bear to wake up so i can tune and test or.maybe throw in the garbage. Who knows lol.
My BIL baught it as non runner for 20 bucks. Only ran couple times. Sat on shelf and wont run. Tipicle home owner saw lol.

Sent from my SM-G950W using Tapatalk

I've got two of these and the one was bought new by my dad it never has ran right worst saw hooskie has ever made.

 

[merc_man]

I've got two of these and the one was bought new by my dad it never has ran right worst saw hooskie has ever made.

Carb kit fixed it. Runs good. Quite a slow turd for 40cc. My BIL told me to keep it. Was too slow lol. So i gave it to my son. Now he wants me to muff mod it.

Sent from my SM-G950W using Tapatalk

 

[460 magnum]

Carb kit fixed it. Runs good. Quite a slow turd for 40cc. My BIL told me to keep it. Was too slow lol. So i gave it to my son. Now he wants me to muff mod it.

Sent from my SM-G950W using Tapatalk

I don't know if that will help or not I guess I couldn't hurt

 

[Dub11]

Carb kit fixed it. Runs good. Quite a slow turd for 40cc. My BIL told me to keep it. Was too slow lol. So i gave it to my son. Now he wants me to muff mod it.

Sent from my SM-G950W using Tapatalk

I had a Poulan with the same muffler and popped out them inserts for the screw and drilled some holes in them.


I should also add the first one I did was enlarge the current opening and it made it to louder than need be.