What's on your bench?

[usmcbuckwild]

I’ve tried indexing the plug on a few saws, I think it was just a waste of buying 10 spark plugs (lol) trying to find one that was in proper orientation, but I didn’t time the cuts or anything.

Call me gullible, but Did you really try 10 different plugs?

 

[tickbitintn]

Guy I used to work with a LONG time ago used to keep about 4 boxes (of ten) for every sportbike engine he was working on at the time.....
So 10 is not too far out there!! Lol

Sent from my XT1635-01 using Tapatalk

 

[huskyboy]

Call me gullible, but Did you really try 10 different plugs?

Yep, had a lot on hand from junk saws.

 

[kingOFgEEEks]

Bout to launch this MS192T into orbit. Damn recoil won’t stay together. Starting to wonder what’s wrong inside. Any suggestions?

 

[Matt Ellerbee]

Bout to launch this MS192T into orbit. Damn recoil won’t stay together. Starting to wonder what’s wrong inside. Any suggestions?
View attachment 159479

Launch it my way!

Will it stay together while pulling rope off the saw? The clip that holds everything may be worn and coming off when under pressure.

 

[kingOFgEEEks]

Launch it my way!

Will it stay together while pulling rope off the saw? The clip that holds everything may be worn and coming off when under pressure.

I replaced the banjo clip and pawls when it grenaded last time. I think the coil spring (not the recoil spring, but the other one between the recoil and the pawls) took the brunt when it launched this time.

Would I be better off to put a non ez start pulley in it?

 

[Matt Ellerbee]

I replaced the banjo clip and pawls when it grenaded last time. I think the coil spring (not the recoil spring, but the other one between the recoil and the pawls) took the brunt when it launched this time.

Is it an easy start?

 

[kingOFgEEEks]

Is it an easy start?

Yeah. Stupid design

 

[usmcbuckwild]

I ditchedthe EZ start on the last one I worked on.

 

[Matt Ellerbee]

Yeah. Stupid design

Indeed.

I ditchedthe EZ start on the last one I worked on.

We have a bg86c blower at work, guys kept drop starting it,bending the snot out of the easy start spring. A bit of JB weld later.... all is fixed!

 

[kingOFgEEEks]

I ditchedthe EZ start on the last one I worked on.

Indeed.


We have a bg86c blower at work, guys kept drop starting it,bending the snot out of the easy start spring. A bit of JB weld later.... all is fixed!

That settles it. I'm going to go get a non ez start pulley.

 

[usmcbuckwild]

Indeed.


We have a bg86c blower at work, guys kept drop starting it,bending the snot out of the easy start spring. A bit of JB weld later.... all is fixed!

Recently had a 201 with a FUBAR EZstart spring, basically same as your issue. Cut the spring down, bent a new hook and re-installed. Seems to Work way mo betterfull now.

 

[Matt Ellerbee]

That settles it. I'm going to go get a non ez start pulley.

You will need to swap the shaft also. The Ezstart is longer cause of the extra stuff in there. It’d probably be easier to get a whole new(used) recoil cover and sell yours.

 

[Tor R]

A colleague to my logger buddy came with this trio today, stored in a humid farm building, 257 - 42 special - 254:


None of them are scored, all 3 locked, I don't give them much of a chance:


2152 Porting job. Dunno how many I've seen like this, 10 last 2 years maybe, more often on those with metal clamp.

 

[weeks auto]

If you need a new recoil I might have a good used complete setup off a 192tc you can have

 

[weeks auto]

Bout to launch this MS192T into orbit. Damn recoil won’t stay together. Starting to wonder what’s wrong inside. Any suggestions?
View attachment 159479

 

[redline4]

At work workbench.
Where nothing fun ever takes place.

Gm 2.4. Blew out the rear crank seal and drove until it shut off. Added oil. Drove again. Shut off. Added oil..
3 farkin times!



Mains survived. All new bearings, crank and rods going in.

 

[Evansaw]

My new arrival MMWS cylinder and muffler

 

[BonScott46]

My new arrival MMWS cylinder and muffler

For God's sake man what saw is it going on? CAD demands to know!

 

[BonScott46]

Replaced the original oil line in a 10mm 044 today. Oils a 24 with some to spare where it was only keeping up with a 20 before. These units were listed at 5.9kg with a 330ml (661 is 360ml) oil tank and 800ml fuel tank(661 is 825ml). Oiler is rated at 8-18ml/min. Damn fine worksaw with only a opened up muffler.