The Swap Meet Thread

[Backtroller]

Thanks I’d appreciate that.

 

[P.M.P.]

Thanks I’d appreciate that.

It's got a bolt through it. Looks like it would clean up good.

 

[P.M.P.]

I'll take the bolt out later to see if it's there to hold presence lever down and separate to make sure it's good. If you need something else I can send it. I can clean it see what it looks like.

 

[trooney]

Its probably to hold the trigger on

 

[cuinrearview]

Anyone in here got any 359 parts? Asking for a Canadian friend.

Also I could use a couple muffler heat shields and rim drums for a 350. A FW side case for a 359/7. I have Husky 141s to trade. Or good parts. Or cash.

 

[dahmer]

These are older than me but work great for my use. The dogs are approximately 6”-7” long and each chain leg is approximately 24” long each. If you see a set of these for sale let me know the price. Thanks.

 

[decableguy2000]

Need a brake spring for a Husqvarna 281, 288, 394 or Jonsered 2095 Part #"503 64 49-01". it is no longer available. It would be in the 1 st gen 394 brake and the 1st gen plastic handle brake on the 281/288. I have all the NOS parts needed to reassemble a 281/288 brake except for this. would be early 90s models

 

[Mastermind]

Any of you futhermuckers got a decent 064 jug?

 

[jk14]

Any of you futhermuckers got a decent 064 jug?

Fink I mite. I'll take a look in the morning when I get to the shop.

 

[Frankavich84]

Any of you futhermuckers got a decent 064 jug?

I know I’ve got 3-4 KS jugs and maybe a Mahle


Sent from my iPhone using Tapatalk

 

[Mastermind]

Fink I mite. I'll take a look in the morning when I get to the shop.

I know I’ve got 3-4 KS jugs and maybe a Mahle


Sent from my iPhone using Tapatalk

Welp....one of our members asked me about fixing up a jug for him. Got some transfer, chipping around a couple of ports from a bearing failure, steel particles embedded in the squish band, and a stripped plug hole.

I figured it would be so much better to start with a good jug instead.

 

[AlfA01]

Fink I mite. I'll take a look in the morning when I get to the shop.

I know I’ve got 3-4 KS jugs and maybe a Mahle


Sent from my iPhone using Tapatalk

I'm kind of needing one of those myself...if you fellas need something I got stuffs to trade.

 

[Mastermind]

OK gents......found my jug.

This forum.....and it's members are top fuggin notch !!!!!

 

[Frank bierce]

just picked up an ohsixfo project

 

[Frank bierce]

Here it is...

 

[jacob j.]

I think that cylinder can be saved.

 

[Jimmy in NC]

I think that cylinder can be saved.

The patina has to go though...

 

[cuinrearview]

That looks better than half that I clean up.

I'm looking for a coil, specifically just a good coil wire, for a 2139t or 335/338xpt. I'm getting some erratic behavior and I have isolated the ignition. There's some wear on the sheathing I don't like.

 

[Mastermind]

That looks better than half that I clean up.

I'm looking for a coil, specifically just a good coil wire, for a 2139t or 335/338xpt. I'm getting some erratic behavior and I have isolated the ignition. There's some wear on the sheathing I don't like.

I have rolls of Stihl spark lead. How long?

 

[dahmer]

Anybody need a Stihl, 3/8, .063, 70 dl chain? Came in a package deal. Cutters are barely used, not rocked. Looks like he threw the chain and didn’t know to file the dl dings to get it to fit back in the bar groove. You pay shipping.