JONSERED Jonsereds

[Czed]

Finally found a Jonsered I’ve wanted for a while. Bought off of a member. It’s 2166 I have yet to run it but it sure looks nice I’ll be grinding on the transfers and mm it shortly View attachment 127500View attachment 127501View attachment 127502View attachment 127503View attachment 127504

When you gonna sell it to me?

 

[Czed]

Finally found a Jonsered I’ve wanted for a while. Bought off of a member. It’s 2166 I have yet to run it but it sure looks nice I’ll be grinding on the transfers and mm it shortly View attachment 127500View attachment 127501View attachment 127502View attachment 127503View attachment 127504

Needs a fullwrap

 

[Backtroller]

When you gonna sell it to me?

Needs a fullwrap

Wrap is on its way

I should probably try it first

 

[WKEND LUMBERJAK]

Looking for a Jonsered 930 air filter cover 503 15 29-01 According to Ipl its the same a a 830 also

 

[67L36Driver]

Looking for a Jonsered 930 air filter cover 503 15 29-01 According to Ipl its the same a a 830 also

You may have to resort to Ebay Europe Kenneth. [emoji848]

 

[Cut4fun]

1995

 

[WKEND LUMBERJAK]

1995

View attachment 129952

2083?

 

[Cut4fun]

2083?

Yep

Bought not running needing alot of parts replaced. Something I happen to have on hand for these.

 

[Jon1212]

http://www.jonsered.com/ca/en/chainsaws/cs-2258/

New fangled contraptions cause me no small measure of trepidation, but am I reading the info correctly? Is this model an AutoTune © saw?

 

[NCFarmboy]

Yes, AutoTune.
Shep

 

[Jon1212]

Yes, AutoTune.
Shep

Thank you. I figured that's what they meant in the model info, but it wasn't altogether too clear.

 

[Backtroller]

2166 modified to 2172

 

[heimannm]

Does anyone know if a points replacement chip like the Nova can be used to replace the trigger on a 70E?

Original part 504 62 00 17 is very hard to find and costs $90+ if you can find one.

Thanks,

Mark

 

[NCFarmboy]

Have a Jonsered 630 Super 2 on my bench. Rebuilt starter from my NOS parts stash. Next carb rebuild and fuel lines. Carb is a Tillotson HS257a. Looked it up on Tilly website. It's not listed. Found it on page 6 of my 630 IPL PN: 503-2803-15 Recirculation carburetor. Does take reg RK23/DG5HS carb. kit.
Never ran across one before. Pop off is 7 psi/.5 bar. Should it be more? I'm thinking 15 psi. Anyone know anything about this carb.?
Shep

 

[67L36Driver]

J-red CS 2236T.
Good?
Bad?
Meh?

 

[67L36Driver]

Dead in here!

 

[old 040]

2077 with 064 piston assy.......

 

[KYsawman]

Just got this one, my first j-red. Installed good used cylinder, new bearings and seals,metal intake clamp, new fuel lines, and muffler mod. Started up and ran great, now the seam in the oil tank is leaking.

 

[Dub11]

View attachment 138097 View attachment 138098 Just got this one, my first j-red. Installed good used cylinder, new bearings and seals,metal intake clamp, new fuel lines, and muffler mod. Started up and ran great, now the seam in the oil tank is leaking.

Gonna slather the seam in JB weld? And what head is on it?

 

[KYsawman]

get

Gonna slather the seam in JB weld? And what head is on it?

I tried that but didn’t work, found a used one on eBay and have it coming. The seam is leaking under the coil area by where the cylinder bolts down. There is not much room to cover the seam with sealer and not interfere with base sealing. It is stock 45cc for now, I have the riser or as husqvarna called it a bearing cup. I might just go ahead and put it in and put the 346xp top end on it too.