Dolmar 64xx/73xx/79xx series, smurfs and solo 665/675/681 thread

[SOS Ridgerider]

Husky 562 caps fit these saws.

Edit: see post above. We posted at the same time lol.

 

[Backtroller]

Same as the caps on the 357/359/562/2166/2172. These are aftermarket Stens. I made a post earlier about dying caps black for a Jonsered. Not sure how to paste the link here.

 

[Deets066]

I became frustrated with the bar oil cap that I couldn’t budge with my fingers and had to walk to get my wrench. Not a big deal but since I had just dyed some aftermarket caps for my 2172 black, I thought why not? I had an extra set and boiled some water and RIT dye and an hour later they are black.

Another member here had used some Husky caps before so this isn’t a new idea.

You don’t carry a wrench in you pocket when cuttin?

 

[hseII]

You don’t carry a wrench in you pocket when cuttin?

Nos

Sent from my iPhone using Jon1212 Pro

 

[3browns]

Direct crossover. Mine fit perfect.

Can’t remember want to say 562 but may be wrong.

I found this thread and I think it will sort me out

http://opeforum.com/threads/jonsered-black-flippy-caps.14360/page-2

Many thanks

 

[Deets066]

Nos

Sent from my iPhone using Jon1212 Pro

MR. PNW

 

[hseII]

MR. PNW

It’s just so Darn Handy, that wrap & tool holder.

I <3 Tool Holders.


Sent from my iPhone using Jon1212 Pro

 

[T.Roller]

Good to know about the caps

 

[Backtroller]

You don’t carry a wrench in you pocket when cuttin?

Not today. I didn’t have extra gas or oil either. I just went out to see if my Oiler mod helped. I stopped to see how much was left and that’s when I couldn’t.

It seemed to help though. It was oiling my 28” well. Much better than before.

 

[huskyboy]

Not today. I didn’t have extra gas or oil either. I just went out to see if my Oiler mod helped. I stopped to see how much was left and that’s when I couldn’t.

It seemed to help though. It was oiling my 28” well. Much better than before.

Yeah makes a big difference modding the oiler on them

 

[T.Roller]

Mine oils a 28" more than needed so I don't plan to touch the oiler.

 

[Backtroller]

Mine didn’t do so great. I opened the holes up my sugi and I thought that might help (a little). This helped big time. I didn’t go too extreme.

 

[T.Roller]

Mine didn’t do so great. I opened the holes up my sugi and I thought that might help (a little). This helped big time. I didn’t go too extreme.

That sucks

 

[huskyboy]

Mine oiled a 24 better than my 046/461 did but I wanted a little more “insurance” for a 32” if I wanted to run that. I took off just enough off the ramp so oil used is about 1:1 with gas now turned up to max. Pisses oil off a 24 now.

 

[T.Roller]

Mine oiled a 24 better than my 046/461 did but I wanted a little more “insurance” for a 32” if I wanted to run that. I took off just enough off the ramp so oil used is about 1:1 with gas now turned up to max. Pisses oil off a 24 now.

I have a saw or two for every bar size I have. No need to do that lol

 

[Deets066]

Bar oil is expensive, I turn my oilers all the way down....

 

[huskyboy]

I have a saw or two for every bar size I have. No need to do that lol

I wish I was that kool

 

[T.Roller]

I wish I was that kool

Maybe one day....

 

[T.Roller]

Bar oil is expensive, I turn my oilers all the way down....

You don't need much to cut cants

 

[RI Chevy]

Bar oil is expensive, I turn my oilers all the way down....

You're very ECO friendly!