SOLD Clean Sachs-Dolmar 166 w/32" bar - keeping it

[speedyjyj]

She's clean inside and out. Cosmetically a 9.5/10, but not quite minty IMO. New plug, air filter washed, bar dressed, chain sharpened. Idles wonderfully, as it should, pumps oil as it should. I'll take more photos and add details shortly but gauging interest/best offers. Located just North of Toronto. No trades but will ship.

There's not been many hours of run time on this one and was stored for many years before I got it. I bought it for milling but might go to a different powerhead. Still thinking on it.

Video link here:

Thanks for looking.

 

[rocco490]

WOW THIS IS NICE!!!!! This will not last long awesome saw

 

[mgr1]

That is a nice one!

 

[huskyboy]

That’s gotta be one of the most badass idles out there...

 

[speedyjyj]

 

[cus_deluxe]

I'll take more photos and add details shortly but gauging interest/best offers.

That last part never works out well. If you want to sell it, then you’ll have to put a price on it. My $.02

 

[speedyjyj]

That last part never works out well. If you want to sell it, then you’ll have to put a price on it. My $.02

I get you. I was thinking of a price recently but can find a reference anywhere. Trying to be fair but considering condition, rarity and so on it's tough. I'll take a whack of photos over the weekend and update the thread to give out as much information as I can.

 

[Wood Chopper]

@166.


Sent from my iPhone using Tapatalk

 

[cus_deluxe]

I get you. I was thinking of a price recently but can find a reference anywhere. Trying to be fair but considering condition, rarity and so on it's tough. I'll take a whack of photos over the weekend and update the thread to give out as much information as I can.

Yep i understand that. i think @Lee H has 1 or 2 of these (lol).....he may be able to help you with a rough “market value”

 

[rocco490]

If your open to offers I will start it at $700 usd for pho

 

[jacob j.]

Yep i understand that. i think @Lee H has 1 or 2 of these (lol).....he may be able to help you with a rough “market value”

Lee is as honest as they come and is very forthright about prices.

 

[speedyjyj]

Ok. Some more photos and some detail.

 

[speedyjyj]

 

[speedyjyj]

 

[speedyjyj]

As for details. The reason it’s a 9.5/10 and not minty IMO is the sprocket cover has a scratch in the paint and the sticker is somewhat mangled. The real issue for me is the muffler. It has no leaks but needs the correct fastener installed on one of the bolts, sand blasted and painted. The rear handle and the remainder of the saw seems pretty good. I forgot to take photos of the bott0m of the saw - I’ll post that in a bit. It really runs great and I will provide a compression test when I get time over the weekend.

That’s all I can think of right now.

 

[Lee H]

Nice saw, Whats up with the one muffler bolt. Have you removed the muffler
to inspect the piston. I have had quite few of these with bad top ends.

 

[Cut4fun]

If shes a runner that one will bring 1200+ US

The last gas one I sold for 800 US with 30" few years back.

If your patient you can buy them priced right and much cheaper.

 

[speedyjyj]

Next steps this weekend:

Check top end for scoring
Find (possibly) proper fastener for the muffler oddball that’s in there now.
Check compression
Change fuel filter (if it needs it)

And I’ll take photos of the bottom, sprocket and clutch to answer any questions.

Thanks for all the feedback folks.

 

[speedyjyj]

Top end shots are below. All muffler bolts came out without fight whatsoever.

 

[Lightning Performance]

800