661 port job for free
- Thread starter jmssaws
- Start date
Redfin
Meh...
- Local time
- 5:37 PM
- User ID
- 159
- Joined
- Dec 24, 2015
- Messages
- 7,645
- Reaction score
- 39,982
- Location
- Central Pa
leadfarmer
Hot Rod !!!
- Local time
- 5:37 PM
- User ID
- 300
- Joined
- Dec 28, 2015
- Messages
- 10,074
- Reaction score
- 71,164
- Location
- S Central PA
Boy that was quick
CR500
Pinnacle OPE Member
- Local time
- 5:37 PM
- User ID
- 745
- Joined
- Jan 31, 2016
- Messages
- 749
- Reaction score
- 1,673
- Location
- Western NY
Test that jug of mine lol
Sent from my non internal combustion device.
Sent from my non internal combustion device.
- Local time
- 4:37 PM
- User ID
- 4
- Joined
- Dec 3, 2015
- Messages
- 47,949
- Reaction score
- 311,161
- Location
- Banner Springs Tennessee
That was quick. Which is an indication that you are well respected my friend. 
Keith Gandy
Maxima K2 40:1 87 Pump Gas
- Local time
- 4:37 PM
- User ID
- 341
- Joined
- Dec 30, 2015
- Messages
- 6,207
- Reaction score
- 16,189
- Location
- Provencal, Louisiana
I remember u did the same for me on the 461. There was some poutin son of a guns in line behind me that day!!! Lol!That was quick. Which is an indication that you are well respected my friend.
- Local time
- 4:37 PM
- User ID
- 4
- Joined
- Dec 3, 2015
- Messages
- 47,949
- Reaction score
- 311,161
- Location
- Banner Springs Tennessee
I did that for a lot of saws Keith. MS241C, MS62C, MS461........and others probably.
Keith Gandy
Maxima K2 40:1 87 Pump Gas
- Local time
- 4:37 PM
- User ID
- 341
- Joined
- Dec 30, 2015
- Messages
- 6,207
- Reaction score
- 16,189
- Location
- Provencal, Louisiana
That 461 made 7.1hp at 10000rpm
- Local time
- 4:37 PM
- User ID
- 4
- Joined
- Dec 3, 2015
- Messages
- 47,949
- Reaction score
- 311,161
- Location
- Banner Springs Tennessee
If I remember right Brad built one that topped it though.
Keith Gandy
Maxima K2 40:1 87 Pump Gas
- Local time
- 4:37 PM
- User ID
- 341
- Joined
- Dec 30, 2015
- Messages
- 6,207
- Reaction score
- 16,189
- Location
- Provencal, Louisiana
I think it was 7.7 or around?
Backtroller
Here For The Long Haul!
- Local time
- 4:37 PM
- User ID
- 349
- Joined
- Dec 31, 2015
- Messages
- 2,791
- Reaction score
- 11,312
- Location
- Land of Badgers
CR500
Pinnacle OPE Member
- Local time
- 5:37 PM
- User ID
- 745
- Joined
- Jan 31, 2016
- Messages
- 749
- Reaction score
- 1,673
- Location
- Western NY
So I gotta send my saw back now after this idea works lol?
Sent from my non internal combustion device.
Sent from my non internal combustion device.
MustangMike
Mastermind Approved!
- Local time
- 5:37 PM
- User ID
- 338
- Joined
- Dec 30, 2015
- Messages
- 11,433
- Reaction score
- 35,921
- Location
- Brewster, NY
Different dyno, different saws, and different day, so not really comparable, but both the 460 Randy did for me, and the one Dr Al did for me (both with 046 D jugs) produced over 8 Hp at the CT GTG on their dyno, and I didn't even clean the air filters before the runs!
