Search results

Husky 55 Rancher in really nice condition. Piston is scored, I haven't looked into why. It runs, but won't hold a tune. Comes with an OEM p&c. PayPal preferred. I have $200 in it so that's what I'm asking, plus shipping. Thanks.

For trade is this very nice 272xp. Oils and runs as it should and is a very clean example of this saw. New AM as well as the original muffler which has been modded. Decomp has been plugged and there is some damage to the top cover from the muffler. I'm interested in dolmar/makita 79xx or...

Looking for a nice, clean 50-60cc husky xp in a 2 or 3 series. Let me know what you have. Thanks.

I just bought a new fs240 yesterday and used it til dark trimming the bank behind the house (reason I bought it). I'm happy with it, way more power than my old fs85. I wanted the bigger stihl brushcutter but they start at $1000 and are heavier....I felt like this is a good combo of...

I have an 046 cylinder that I'm wanting to put on an 044/440 for a hybrid build. Let me know what you have. Thanks.

How do you carry your saw on your 4wheeler? Straps slip too much. Been looking at the bolt on type that you slide the bar in. Just looking for ideas. Thanks.

Looking for an 044 gas tank. Thanks.

These are at my local dealer. I always forget to take pics but got them today. I thought some guys here would be interested in the pics....and none are for sale, I asked lol.

A while back I asked a logger buddy of mine if he had any old saws. He just dropped them off. He said I could have them if I figured out why his 261 wasn't oiling. There's an 029, 310, 044, and what I think is a 460...the badge is gone but I'm about to look over the cylinder. P&c look great in...

Looking for a good condition husky 460 clutch cover to put on my 346xp. Thanks.

Always on the lookout for a deal and stumbled on this low hr 346xp yesterday. It cleaned up real nice. Came with a good chain and decent bar too. Will the husky 350 clutch cover for this saw? Do I need a certain tool to adjust the carb? I'm thinking of opening the muffler up a little and want...

What gauge are you guys using? I want to try a couple new ones. Thanks

Does it matter if the control switch is on or off when checking compression? Seems like I have read to make sure it is in the off position for some reason. What about holding the throttle open vs leaving it closed? Thanks

I'm finishing out my shop. Got the ceiling finished yesterday and new 8' led lighting is going up today. Work benches are next I'm looking for ideas on what to put on the tops of the work bences. Plywood with sheet metal? Some kind of laminate or old countertop? I want to avoid bare plywood so...

What makes it so special? I read tons of post praising the saw and it seems very sought after, I'm wondering what the appeal is? I am going to look at a couple non running 044 later this week, asked an old buddy who logs if he had any old saws and he said he thinks he has a couple 044's. Post...

New to rebuilding and figuring out I should diagnosis the problem before tearing a saw down after a scored piston. Got this saw apart because scoring was harsh on exhaust side and intake side looked clean. Now that its tore down, there is scoring below the ring pins on the intake side. I took...

I'm getting ready to rebuild an 029 with an 039 top end. Owner put an AM carb on it (as well as AM fuel line, fuel filter and air filter) in an attempt to get it to run but P&C is toast. I've never rebuilt a carb but would you go with the AM carb or just rebuild the stock carb? Thanks

I found a saw for sale in Halifax, NC but it's about 3 hrs from me. Is anyone close by that could help a brother out? I talked to the seller and he seems like a nice guy so there shouldn't be anything to worry about. Thanks.

Buddy give me an ms290 to get running after he tried putting on a new AM carb, fuel line and filter, and a new filter. Asked him if he'd looked at the piston, he said no. This is what it looks like....... Thinking this would be a good candidate for an 039 top end. Is this a direct bolt on and...