High Quality Chainsaw Bars Husqvarna Toys

Search results

  1. 94BULLITT

    Check out My YouTube Channel

    Thanks! Sent from my SM-G965U using Tapatalk
  2. 94BULLITT

    Check out My YouTube Channel

    I subscribed to your channel too. You have some videos that look interesting. Sent from my SM-G965U using Tapatalk
  3. 94BULLITT

    372 assembly question?

    I think it is $4 at the dealer but I can't drive to the dealer for $3 plus it would take a week to get it. Sent from my SM-G965U using Tapatalk
  4. 94BULLITT

    372 assembly question?

    I can see where it is supposed to be. Sent from my SM-G965U using Tapatalk
  5. 94BULLITT

    372 assembly question?

    I ordered this. https://www.ebay.com/itm/274636140748 Sent from my SM-G965U using Tapatalk
  6. 94BULLITT

    372 assembly question?

    They could have done something better. At least they didn't put a stack of washers in there;)
  7. 94BULLITT

    372 assembly question?

    It is not going back together til I have an oring for it. That is a poor design.
  8. 94BULLITT

    372 assembly question?

    . Sent from my SM-G965U using Tapatalk
  9. 94BULLITT

    372 assembly question?

    I said seal and meant oring.
  10. 94BULLITT

    372 assembly question?

    I cut more than most, but I have a bunch of saws so the run time is shared between several saws. I do seem to run 4 or 5 saws for the part. The 660 kit is really good all though the crank failed in mine after 3 tanks. Everything on that kit fits and works nicely. My chain adjuster is a hair...
  11. 94BULLITT

    372 assembly question?

    No, the seal is missing. I can see the gap between the crank and the bearing.
  12. 94BULLITT

    372 assembly question?

    I'll pull the clutch tomorrow and see if it is there.If not I'll get one. Right now the saw is 99% farmertec, expect Stihl bolt and nut that was not included. I was going to run it a little and see what needed upgraded and get it all at once. I built 2 of these farmetec saws last week. This...
  13. 94BULLITT

    372 assembly question?

    My seals were already installed. Sent from my SM-G965U using Tapatalk
  14. 94BULLITT

    372 assembly question?

    I looked at the ipl when I was putting it together. The IPL showed the bushing, clutch, clutch drum etc. It didn't show the o ring. The o ring is shown with the crank, crank bearings, seals and the bushing is also shown again. The husqvarna ipl is a little weird. Was the o ring already on you...
  15. 94BULLITT

    372 assembly question?

    Thanks, is that the bolt without threads on the end? Sent from my SM-G965U using Tapatalk
  16. 94BULLITT

    372 assembly question?

    You guys were both right. Thanks for the help. I had to center the carb with out the tubing on the bolts so the choke would work. Now I don't have to do that. Should there be bushing on the crankcase here? There is a bolt hole there. I am out of bushings. Sent from my SM-G965U using Tapatalk
  17. 94BULLITT

    372 assembly question?

    Thanks, that makes sense. What are the hoses for? Something to drive me crazy?
  18. 94BULLITT

    372 assembly question?

    I'm building a 372 and I can't figure out where these parts go. What are they for? Sent from my SM-G965U using Tapatalk
  19. 94BULLITT

    Let's see some ratchets

    Here are my long handle 1/4," 3/8," and 1/2" ratchets. Sent from my SM-G950U using Tapatalk
  20. 94BULLITT

    Firewood conveyors

    I have a 16' feed conveyor that I converted into a firewood conveyor. I is powered by a gas engine. I made this video on my YouTube channel. I was back to the middle of the pile when I checked the wood.
Top