High Quality Chainsaw Bars Husqvarna Toys

Search results

  1. old guy

    Knock-off No-Spill gas cans

    I'm 83 years old and I have never found anything as good as the no-spill cans, I can lift the heavy 5 gallon up on the tractor put the spout in the gas hole & push the button, none of the trying to get the spout in the hole before the gas flows, same with saws on the ground, put the spout in the...
  2. old guy

    SELLING 346 OE, other 2 sold

    Always read higher cold!
  3. old guy

    Knife Sharpening

    It has been many years since I trapped beaver, maybe I didn't sharpen that often but others with cheap knives did. My best knife at that time (1960s) was the little swedish birch handled laminated blades with the hard center laminate, these took a razor edge, I once took a curl off the side of a...
  4. old guy

    Knife Sharpening

    I see people putting a whole lot more effert into this than I would. Have you ever skinned a beaver, nothing dulls a blade faster, every inch must be cut away, your sharpening methods would double the time as it sometimes takes three sharpens on a big beaver if your skinning clean.
  5. old guy

    Knife Sharpening

    I have the other kit like the Lansky, my blades are shaving sharp, the Lansky should do the same.
  6. old guy

    SELLING Husqvarna 531307446 24" bar K095

    I have a ported 359 cyl on a 357 bottom, b g delete, muff mod, fed by a 372 carb. It pulls an 8 pin with 18" bar, makes long chips.
  7. old guy

    SELLING Husqvarna 531307446 24" bar K095

    I think somebody on the other forum is looking for one of them. My Huskvarna 358 could pull that bar, but I have enough crap.
  8. old guy

    Tell me a joke.....

    So, Philbert! I don't recall your last name, was it Woods? or maybe Plantation?
  9. old guy

    SELLING Tsumara bars will be in stock

    He sent me one of those 24" premium light bars from the raffle, I put it on a ported 372 and threw a new husky c83 chain on it then buried it in some dead red oak logs, oh man! did that combo cut!. No floppyness in the bar & it balanced that saw perfectly.
  10. old guy

    Fundraiser for family of Stevetheboatguy

    My Tsumura bar arrived today from MG2186, it is mighty fine looking bar.
  11. old guy

    Fundraiser for family of Stevetheboatguy

    Thank You.
  12. old guy

    Fundraiser for family of Stevetheboatguy

    I tried to message @MG2186 to give him my address but he has limmited access.
  13. old guy

    Fundraiser for family of Stevetheboatguy

    I'll go with #8, D009 husky 3/8 .50 thank you.
  14. old guy

    Did You Ever See Such a Farmer Fix?

    I see that huskys are not the only ones that lose screws:p
  15. old guy

    CBN Wheels - which one?

    I have one cbn wheel from Diamond, it works for me.
  16. old guy

    WANTED Stihl 10mm 044 case wanted

    Yeah, I'm so tired of the ice we have here from the rain & freezing. My nieghbor burned all his wood 10-12 cord, as we speak he just dug his way to the pile I have here with his bobcat. Next week sposed to be in the 60's:sun_smiley:
  17. old guy

    WANTED Stihl 10mm 044 case wanted

    Hey John, long time no hear from ya. Ya got enough snow up there?
  18. old guy

    WANTED Stihl 10mm 044 case wanted

    Nah, I gotta keep a couple of stihls around to avoid snobbery with the nieghbors.
  19. old guy

    WANTED Stihl 10mm 044 case wanted

    Yeah, I had seen that info., not being a stihl guy it just didn't stick with me, I do have a 12m/m 044 slant fin with the D cyl.
Top