Search results

Ok fellas, my 4300 has sat since last year and when I went to start it, it started and ran only at an idle. Once I touch the throttle it stalls and dies. One pull restart and same thing, touch the throttle it dies. Figured it a carb issue. Pulled the carb and there was some gunk in the screen...

So I don't really cut wood anymore and have other saws I don't want to part with that can handle bigger jobs. So I guess I'll let her go. This is a 372XPW conversion that I built from an x-torq 372xp and was ported by John (redfin). Base and squish was cut and set to .019" if my memory serves...

Anyone else get this message for post approval lately? Did I do something bad and now I'm in the corner?

Bought this new in March 2020 thinking I would use it a lot more than I do. Has 3 or 4 tanks through it. It's bone stock. How's $300 shipped in the 48 sound?

Got this saw as a basket case. New crank seals, new LRB piston and rings, rebuilt the carb, new fuel line and filter. The cylinder has some porosity in the plating well below the exhaust port. Air filter is in great shape. New starter rope. New starter spring. No torn mounts. The holes in the...

So I have this 6100 that starts great, idles great, runs in the cut great, but from idle to full throttle it has a lean hesitation. Both high and low needles can adjust over lean and flood the engine as well. I can tune out the hesitation. Is there a quick fix common to these reed strato...

There are a bunch of car guys on this forum so here you go. It is currently updated to 16.2 or 2015 and older. It can be updated to current software (20.4) and used on 2020 vehicles. Use the touch screen or menu buttons to navigate. Manufacturer specific scan tool that has access to all...

Have a 4200 apart on my bench and my son decided to misplace the wrist pin. :( Anybody have one? I'll buy a whole parts saw if I have to.

Looking for two tsumura light bars 16" .325 .050 small husky mount 20" 3\8 .050 small husky mount. Let me know what you got. I have American Freedom Notes or stuffs to trade. :) EDIT: I will also take a stihl mount 16" .325 .050 bar and use an adaptor.

These are original Toro parts. 13 x 6.5 x 6 with a 1/2" axle bolt. Asking $200 plus shipping.

Selling my this because i dont use it since i bought my 355t. Had this saw for 6 years always been reliable. Bought it as a home depot return. I removed the cat from the muffler. $100 shipped to the 48.

Got this to see if i wanted to shell out the coin for a 5100. Starts and runs well. I uncrimped the muffler and gutted it, and crimped it back together. Rebuilt the carb and defeated the carb screw locks. It now has a fully adjustable carb. Looks decent, the orange plastic has some fading...

Bought this saw new in January of 2017. Starts, runs, and cuts like it should. Has the AT12 carb. Has all its gray paint just marred up. Saw is bone stock. Not even a muffler mod! $450 PHO plus the ride.

Looking for a good usable p/c. Thanks, Steve.

Whatcha got? Let me know.

Im looking for a 50cc Makita saw to be the little brother to my 7910. Must be the blue/teal color. Really wanting a 5105, or a 5121. Im open to others. Let me know what you have and how much. Thanks, Steve.

So i need a new trimmer. I trim a large hillside by the road that takes. A little over an hour to do. I have the 2620U brush cutter and am impressed with its power but is heavy without the harness. I see the 2320T has the high torque head and is a few pounds lighter than the 2620. Weight is...

Have a complete 3-10E block and starter/generator. Has the coil spacer and longer screws. Resistor is there. Brushes and commutator all look great. The muffler was rusted on this and has rust bits in the cylinder. Will need to completely disassembled and cleaned but is in good shape. A good...

I have this 031 that has been sitting for a long time. Feels like great compression. Runs if you put mix down the carb. Have not put mix or oil in either tank to test. Just a nice project saw. Asking $ 50 plus shipping.

Works as it should. 30 shipped OBO.