Search results

New in box 390xp. Euro spec saw so it has the low top set up. It’s still sealed in the box but can open to take pics. $850 plus shipping.

Sold Pending Funds I have a new, never fueled 385xp. Included are the owners manual and kit that came with it. Saw is perfect with no defects. Will take more pics. $750 plus shipping

SPF New Jonsered 2166 for sale. One of the R branded eBay saws. Saw is perfect, no defects and doesn’t appear to have been run. Comes with Jonsered branded bar and chain. $450 plus shipping

Super clean 346 OE. I bought it as a project, it was missing the p&c, intake tract and carb. I’m assuming it had been straight gassed. I split it and installed OEM bearings and seals. OEM p&c, carb and intake tract. Nothing aftermarket on the saw. Very strong and I have only run it to tune and...

Very clean, one owner 357xp. Low hour saw. It had the auto decomp on it. I removed it, tapped and plugged it. While the cylinder was off I installed a new ring and deleted the base gasket. Saw is very strong. I will take more pics if there’s interest. $425 plus shipping.

I have a complete Stihl 046 bottom end. Flywheel and coil included. Was a stout running saw but was run over on a job site. Cases are in nice shape, no cracks, rod is tight and bearings feel smooth.Also have the recoil assembly and carb. Will include a 24” Total light weight bar. Bar has a...

I need a pto side case 1/2 for a 372 x torq Thanks Andy

Sold pending funds. Nice stihl USG grinder for sale. I bought and didn't get around to setting it up. I did run it to make sure it works. Comes with hedge clipper attachment. I believe it's a 2012 model. Original manual is included. No grinding wheels and the original plastic eye shield was...

Mint 390xp. I bought it and discovered the case had a crack in it below the bar stud. I bought new OEM cases and also replaced the clutch cover, cylinder cover, fuel tank, muffler, and recoil. There was nothing wrong with the old stuff but I have OCD and wanted it all to match. P&C were perfect...

Very nice Masterminded 346xp NE for sale. I bought the saw as a builder with a bad cylinder. I split the cases and installed new OEM seals and bearings. Sent the saw to Randy to be ported along with the following new OEM parts: p&c, recoil, clutch cover, cylinder cover, complete intake tract...

Mint condition Masterminded 372xp for sale. Saw was built off a low hour crank. Other than the flywheel nearly everything else is new OEM. New cases, recoil, wide discharge clutch cover, recoil, fuel tank, full wrap handle, OEM p&c , muffler and heat shield. Saw has a 1/4 of a tank thru it since...

Clean 371XP for sale. Bought it from an older gentleman who has owned it since new. Saw ran great, had 135 psi compression when I got it. I had a new single ring Meteor piston so I went ahead and put a new piston and ring in it and deleted the base gasket. I will get another compression reading...

I have the following 385/390xp parts to sell $75 plus shipping for the whole lot, individual prices below 1 used cylinder and HD cover. Has a couple of small cracks that were repaired with JB weld. Fully functional $30 plus shipping 1 NOS cylinder cover $25 plus shipping 1 used recoil had a...

Looking for a 210" muffler and wrap handle. Doesn't need to be mint, just functional.

Anyone live near Mansfield, Ohio?

Looking for a couple of 372xp cylinders, non xt

Very nice 346 xp for sale. 2003 saw. I bought it a few weeks ago from another member. A week later my MMWS 346 came and my don't need two 346's. Saw hasn't seen much use. I painted the muffler and replace the decal on the clutch cover. I paid $425 for the saw and $5 for the decal. Looking to...

I have the following 288 parts for sale / trade: 1 NOS High top cover 1 used High top cover 2 NOS HD Carb elbows 2 used HD carb elbows 2 New HD air filters 1 nice used HD air filters 1 brand new ignition set 1 nice flywheel with pawls 2 new tank vents 1 complete recoil 1 recoil cover 3 good...

Here's the second 288 I have for sale. Started life as a 281. I had the cases powder coated and installed new OEM bearings/seals. Has a very nice used Mahle p&c with a new caber ring. Has the following new OEM parts on it: fuel tank, handle, air filter, muffler and clutch cover. It has a mint...

Completely rebuilt 394 XP high top for sale. I bought the saw as part of a package of saws last year. I was told the coil was bad. It sat for a couple of months as I worked thru the saws. After pulling the muffler I found some scoring on the piston. I pulled the cylinder and sent it to my skinny...