Search results

Found this rag at work today.

Nice exhaust lobe on this am Briggs Cam after 2 hours use. From a JD ride on I fixed today.

rather large unit

Hi Gents. Can get an 044 at the local pawn shop for $400AU. Good condition. Metal tag. Stihl slant fin jug. Good compression. Has the reddish (not orange) plastics. At Aussie prices I was expecting about $6-700. Thoughts? Cheers Chris.

Hi All. Am looking at a AM MS390 Case. The new case is p# 11270203003. My case is 11270210800. Is the new case an updated p#? BTW saw was run over with tractor (not by me lol).Not a good look. Thanks in advance Chris.

Hi gents Do any of you guys use blue demon mig wire? Thinking of getting some for my gasless mig. Seems to get very good reviews. And I can get it here down under. Cheers Chris.

Hi all. So after the am 066 crank thread I will start a new thread. Any one bought other NW parts? I have sent them a couple of emails but no reply. Are they slow to reply ,if others have dealt with them can you let me know. Cheers Chris.

Don't want to start an oil thread but does anyone use it. Cheers Chris.

Hi All, Do these reds put to fine of a finish on cylinders, eg ring bedding? Or is this what people use? Thanks in advance,Chris.

Hi all Dad has a scorpion that if you don't use it for a few weeks won't pick up fuel (vac operated pump). Been a bit problem since new (should of returned for refund but kept) but gotten worse. If you remove vac hose and give it a couple of sucks it picks up. Just seems can't pull over fast...

Hi gents. Looking at rebuilding an 066. This unit is a small (oil) tank 066,but has a poly crank with the larger fw side seal. I thought all small tanks had the small ally crank with the small seal. I know you can't fit a poly crank in an ally saw as the poly crank is wider by about 5mm. All the...

Even though I am down under I have been following them since the Oilers, (Warren Moon as QB). Good to see them doing well. Have had some lean years.

Using different case halves (066 small tank).YES/NO/PROBLEMS. Main AV mount broken on original. Cheers,Chris.

Hi,do you guys use scotch brite balls or flappers for cylinders? Also what size?I assume 2" for say an 066 cylinder (54mm). Cheers,Chris

Hi all,is there a pawl spring I can fit to my 038 to make it dual pawl? All the springs I see for 038 is only single.Will 044,066 fit? It has heaps of compression and would rather trust 2 pawls,or is 1 OK? Cheers,Chris.

Hi all at OPE.I am working on an 038 (no top cover),piston is 52mm,dual port muffler.S# 3382xxx49. I take this to be a Magnum? Cheers,Chris.

Hi all,checking a saw today and coil seems toast.Was going to be a project for me.Assume it is an 038,no covers on saw but has 1119 under fuel tank.Done all the usual coil checks, and ohms readings seem a bit suspect.So do i need an 038 coil or will something else fit?Flywheel P# unknown at this...

Hi all at OPE.What do you think of this cylinder?Is the plating coming off around the ports? Might of been a project for me to put it on an 044 12mm case.Not going to put too much money into it as I don't really need the saw.Would it be any better than my 044 10mm? What other problems could i...

Hi all.Might be able to get an 039 cheap.Piston scored,ring stuck in groove,no compression.Don't know cylinder condition yet.Is this saw worth fixing?Would do vac/press test before strip down to prove other faults.I can get a Tacsum kit for $125 (Aussie).Are these any good?Wouldn't go OEM as too...

Hi MM,seen your stickers on some saws.Wouldn't mind some to put on my toolbox and saws. Would it be in the "to hard box" to send some to Australia? I fully understand if this is the case. Cheers,Chris.