High Quality Chainsaw Bars Husqvarna Toys

Search results

  1. Aggie2012

    WANTED Stihl FG2 Filing Jig

    Looking for one of these jigs but cant find them anywhere. Maybe their discontinued? I believe they are still being manufactured because a dealer out of Australia is selling them https://www.sunshinecoastmowers.com.au/stihl-filing-tool-fg2 Just dont want to deal with shipping out of country...
  2. Aggie2012

    Piston hit Plug

    Good morning gents Hope you all had a good weekend. Question for any one that has time to answer. Got an MS 261 m Tronic that I’m rebuilding for a guy. It was somewhat hard to turn over and after some disassembly found that the clutch drum bearing was missing causing it to be cock eyed...
  3. Aggie2012

    026 Case gasket

    Split this 026 over the weekend because because both bearings were shot. Installed new ones as well as new seals (hopefully I didn't drive these seals in to far) All went together as planned, used oem bearings, seals, and gasket (also added some loctite 518 to the gasket for some added...
  4. Aggie2012

    Stihl 026 Piston size Question

    Working on my first complete tear down and rebuild of an 026. I've got new bearings, used crank I bought online (my original is locked up at the lower needle bearing cage) Impulse line, intake boot, seals, and gaskets. All oem parts Going to try to clean this cylinder up with with my foredom...
  5. Aggie2012

    Stihl 026 piston size help

    Working on my first complete tear down and rebuild of an 026. I've got new bearings, used crank I bought online (my original is locked up at the lower needle bearing cage) Impulse line, intake boot, seals, and gaskets. All oem parts Going to try to clean this cylinder up with with my foredom...
  6. Aggie2012

    Advice needed for dropping this tree

    Hello Gents Wanted to see if y'all might be able to weigh in here on the best way to take out this tree? Should i try and whack off these limbs then tackle the trunk or just go ahead and notch it right away at the trunk? I'd be running a 461 with a 32" bar Tree has not been dead but for a...
  7. Aggie2012

    MS461 high side RPM variance....?

    Good morning men Need some advice or maybe somewhat of an explanation. (I might just be overthinking things) I've got an MS461 that Randy did for me and it runs fantastic. I am trying to keep the RPM's on the high side around 14,200. I start the saw, let it idle for a minute or saw, make a...
  8. Aggie2012

    Ignition system

    Would some of the fine gentlemen on this forum be able to explain how this ignition works? It's from an 015l. I tore it down to here and don't know what to do. I've seen updates for this old style ignition but it sparks just fine. However, I have to use the choke to kill the engine. It...
  9. Aggie2012

    Bent chain or low kickback?

    Evnin gents, So I bought a granburg file n jig and it works great. (Sharpened 5 or 6 chains so far for my smaller saws that run 3/8 lp or picco) Now I get to my 461 that runs a 3/8 chain. Fit pretty tight between the jig but didn't think much of it. Sharpened it without much of a problem...
  10. Aggie2012

    VP 50:1 premixed fuel

    Howdy gents This is my first post so please bear with me. I bought a gallon of Vp racing premixed 50:1 and I'd like to dilute it to 40:1 but I don't have any of the Motul 710 2t to match what's in the can. What's the harm in mixing some stihl ultra that I have in the shop to get this ratio to...
Top