High Quality Chainsaw Bars Husqvarna Toys Hockfire Saws

Search results

  1. JIMG

    Recommend me a gasket material

    I have a couple old machines to put together and I am going to need to cut the case gaskets. I am looking for gasket material suggestions.
  2. JIMG

    SOLD 266se $350

    This one is a solid runner with some upgrades. It has a new windowed meteor piston, base gasket delete, new filters, gaskets, nachi crank bearings, Duke's 272 carb., new clutch and drum, sprocket, shrink tube over the handle, muffler modded a bit, oem cylinder cleaned up, exhaust polished up...
  3. JIMG

    SOLD Stihl 051

    $350 plus shipping With the very good condition big bar and new chain. This one has been completely gone through. New av, lines, filters, gaskets, carb kit, oiler o rings, new aftermarket piston, cylinder cleaned up and exhaust polished. FW side bearing replaced, I have a new needle bearing...
  4. JIMG

    SOLD 181/288

    I have a few things to fund and my 064 is on the way home so this one is up on the block. Husky 181se runner with an oem 288 cylinder and AM piston I got off a member here. No other upgrades. Muffler is stock, timing is stock. New lines, filters, Nachi crank bearings, seals, carb kit. spring...
  5. JIMG

    SOLD Jonsered 2165 with MMWS 2172 Cylinder. $450

    This was a high hour 2165 I got off a member here some time back. It has had all the gaskets seals lines filters and bearings replaced. I got the cylinder off another member here. It is off a 372 xtorq that was ported by mastermind. I opened up the muffler and replaced the handle with an...
  6. JIMG

    FOUND IT Pioneer p38

    Or similar model. A presentable runner or project. I'm not really looking for a minty shelf saw.
  7. JIMG

    SOLD MOFO 026

    Mofo ported 026. The only issue I have had with this saw is the air filter cover coming off sometimes during use. Powerhead, bar and square ground chain. $425 + shipping from zip #13676
  8. JIMG

    Any carvers here? what saws do you like?

    Someone gifted me a stihl dime tip bar some time ago which has got me thinking about giving carving a try. Who carves and what is your set up?
  9. JIMG

    SOLD Husqvarna 262

    For your consideration a good, presentable 262 I picked up off another member. Mahle jug. I have done the following since owning: New gas filter and lines mesh AF Muffler opened up, ss wide mesh spark screen Meteor piston Thinner base gasket installed New crank seals and little o-ring...
  10. JIMG

    FOUND IT 14mm stihl bar, 28" - 32"

    Looking for an inexpensive bar option in 404 or 3/8 to hang off an old Stihl 051 I just got going. Around 32" or close to it. hard nose or sprocket.
  11. JIMG

    SOLD 044 Cylinder

    The cylinder is Mahle. It has a couple of busted fins at the top but seems like it will clean up good and work fine.
  12. JIMG

    SOLD Parts Stihl 056 Mag II

    I have for your consideration an 056 Mag II that I got locally with a busted piston. I broke it down and cleaned it up a bit. The cylinder and crankshaft appear to be in good usable condition. Sem igniton, not tested. Cases look usable, there's a spot of rot in it but not enough that it would...
  13. JIMG

    Jonsereds 90

    Looking for an IPL and Service manual for a battered Jonserds 90 I found.
  14. JIMG

    sticky switch on the 044

    In winter everything is a little harder to do and hurts a little more, little things tend to be a bigger deal. I notice I tend to leave my 044 behind simply because the switch is so stiff on it. With gloves on I have to use the scrench to force the lever down. It finally aggravated me enough...
  15. JIMG

    FOUND IT Husqvarna 181se Cylinder

    Looking for a decent OEM 181SE cylinder and a good piston.
  16. JIMG

    SOLD 2171

    For sale- 2171 ..... I "somehow" ended up with four of this saw model, so time to move a couple along. This one has a new meteor piston, Oem cylinder cleaned up, decomp plugged, nachi crank bearings, muffler mod, carb kit, new filters, even new stickers. I have run probably less than 3 tanks...
  17. JIMG

    SOLD 395

    Clean saw, came to me as a basket case with a replacement top end, bearings and crank. These were removed. It now has a low hour oem cylinder, good used oem crank, nachi bearings, and a meteor piston. Other than bearings and piston this is all oem. I took out the base gasket and gutted the...
  18. JIMG

    SOLD Echo 6700

    I bought this one with a few other saws. It appears to have been run with a loose muffler, the piston is scored. I put a carb kit in and opened up the muffler quite a bit. It was very choked up. I planned on getting a new piston but I really have too many project saws right now. It fires off...
  19. JIMG

    Progress

    Here is some of that walnut I found in somebody's driveway a year or two back. I forged out some bases for it. I can really see what all the fuss over walnut wood is about.
  20. JIMG

    FOUND IT 372xp oe / 2171 OEM Cylinder

    P+C or Cylinder.
Top